manualshive.com logo in svg

Britax safe-n-sound BS0072E-020133, Instructions For Installation & Use

Share
Download
Britax safe-n-sound BS0072E-020133 Instructions For Installation & Use Download Page 34

34

Instructions for Installation & Use

 

10° to 15°

ANGULAR ADJUSTMENT OF RESTRAINT

Some vehicle seats have more rearward slope than others. If the angle of the seat causes the baby to 
be too upright for comfort, the angle may be altered by placing a firm packing between the seat and the 
underside of the base. Packing can be a firmly rolled up towel.
If the car's seat is flat then some packing may be required at the front edge of the base to achieve the 
recline angle.

Do not remove all of the installation angle by over packing. Always leave an angle of approximately                     
10°- 15°.

The stabilising bar does 
not need to contact the 
seatback provided the 
seatbelt is tight when 
packing is used.

Rolled towel packing

HOW TO INST

ALL USING SEA

TBEL

T

Summary of Contents for safe-n-sound BS0072E-020133





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands