Brinkmann 810-6419-2, Owner'S Manual

Page: 11 / 64

L LIIG GH HT TIIN NG G IIN NS ST TR RU UC CT TIIO ON NS S::
F Fo ollllo ow w tth he e iin ns sttrru uc cttiio on ns s e ex xa ac cttlly y..
1 1.. O OP PE EN N T TH HE E G GR RIIL LL L L LIID D b be effo orre e a atttte em mp pttiin ng g tto o lliig gh htt a a b bu urrn ne err s so o tth ha att ffu um me es s d do o n no ott a ac cc cu um mu ulla atte e iin ns siid de e
tth he e g grriillll.. A An n e ex xp pllo os siio on n c co ou ulld d o oc cc cu urr iiff g grriillll lliid d iis s d do ow wn n..
2 2.. C Ch he ec ck k tth ha att a allll b bu urrn ne err c co on nttrro oll k kn no ob bs s a an nd d tth he e c cy ylliin nd de err v va allv ve e a arre e ttu urrn ne ed d tto o tth he e " "O OF FF F" " p po os siittiio on n..
3 3.. T Tu urrn n o on n tth he e ffu ue ell s su up pp plly y b by y rro otta attiin ng g tth he e c cy ylliin nd de err v va allv ve e k kn no ob b c co ou un ntte err--c cllo oc ck kw wiis se e tto o ffu ullll o op pe en n..
4 4.. D DO O N NO OT T s stta an nd d w wiitth h h he ea ad d,, b bo od dy y,, o orr a arrm ms s o ov ve err tth he e g grriillll w wh he en n lliig gh httiin ng g..
L LIIG GH HT TIIN NG G T TH HE E M MA AIIN N B BU UR RN NE ER RS S::
1. Open lid before lighting burner.
2. Make sure all control knobs are in the "OFF" position.
3. Select the burner to be lit. Push and turn the control knob of that
burner to the "HIGH" position.
4. Press the electronic igniter and hold for 3 – 5 seconds to light burner.
5. If ignition does NOT occur in 5 seconds, turn control knob to "OFF",
wait 5 minutes to allow gas to dissipate and repeat lighting
procedure.
6. Repeat steps 3 – 5 for lighting each burner. Always use electronic
igniter for lighting each burner. If burner does not ignite using the
push-button igniter, wait 5 minutes, see "Match Lighting the Main
Burners" section.
7. To turn off, turn each control knob clockwise until it locks in the "OFF" position. This does not turn off
the gas flow from the cylinder.
Note: If burner does not light or flame is too low, you may have spider or other insect blockage in
burner, or the flow limiting device has been activated. See "Burner Assembly/Maintenance"
under Proper Care and Maintenance, or "Regulator Resetting Procedure" under Connecting LP
Cylinder and Hose/Regulator to Grill.
M MA AT TC CH H L LIIG GH HT TIIN NG G T TH HE E M MA AIIN N B BU UR RN NE ER RS S::
1. Open lid before lighting.
2. Turn the burner control knobs to "OFF".
3. Place a paper match in the end of the matchlighter. Strike the
match and place through lighting hole in the left hand side of the
grill to approximately 1/2" (1 to 2 cm) from the burner.
4. Turn on the F FA AR R L LE EF FT T burner control knob to the "HIGH"
position. The burner should light within 5 seconds.
5. If the burner does not light, turn the control knob to "OFF" and
wait 5 minutes for gas to dissipate and repeat lighting procedure.
6. Once lit, light adjacent burners in sequence by pressing in and rotating the control knob to
the "HIGH" position.
7. If the burner does not light within the first few attempts of match lighting, there is a problem with the
gas supply. Turn off the gas at the burner
a an nd d
cylinder.
D DO O N NO OT T
attempt to operate the grill until the
problem is found and corrected. See "Trouble Shooting" section of this manual.
WARNING
10
WARNING
R Re ea ad d,, u un nd de errs stta an nd d a an nd d ffo ollllo ow w a allll w wa arrn niin ng gs s a an nd d iin ns sttrru uc cttiio on ns s c co on ntta aiin ne ed d iin n tth hiis s m ma an nu ua all.. D DO O N NO OT T s sk kiip p
a an ny y o off tth he e w wa arrn niin ng gs s a an nd d iin ns sttrru uc cttiio on ns s c co on ntta aiin ne ed d iin n tth he e p prre ec ce ed diin ng g s se ec cttiio on ns s o off tth hiis s m ma an nu ua all..
Lighting Hole
Matchlighter