background image

 

INTRODUCTION 

This fire is CE approved to the European 
Standard EN 509 and is intended for decorative 
purposes.  

The fire must be installed and serviced by a 
qualified CORGI registered installation engineer 
in accordance with National and Local 
Regulations. 

Servicing should be carried out at least 
annually, but depending upon site conditions 
more frequently. 

RELEVANT STANDARDS 

Building Regulations Part J 
BS 1289 : Part 1 : Pre-cast concrete flue blocks 
BS 5440 : Part 1 : Flues 
BS 5440 : Part 2 : Air Supply 
BS 5871 : Part 1 : Installation of gas appliances 
BS 6891 : Gas Installation 

Before installation ensure that the local 
distribution conditions (identification of the type 
of gas and pressure) and the adjustment of the 
appliance are compatible. 

The Gas Category of this fire is 

II

2H3P

 and is 

available set for either Natural Gas (G20) or LPG 
Propane (G31) check the Gas Type on the burner 
data badge is correctly marked for your gas 
supply. A conversion kit is available separately 
direct from Brilliant or your nearest dealer. 

The fire is fitted with an Oxygen Depletion 
Sensor (ODS) which continuously monitors the 
atmosphere in the room turning off the gas 
supply to the fire if combustion products are 
detected. The ODS must not be adjusted or put 
out of operation and only original 
manufacturer’s replacement parts can be used. 

 

 

 

 

 

 

TECHNICAL INFORMATION 

NATURAL GAS (G20) 

 

 

16/18 Standard  16/18 High 

Heat Input Max (gross): 

7.0 kW 

  9.0kW 

Heat Input Min (gross):  

4.1 kW 

  4.4kW 

Inlet Pressure: 

 

20 mbar 

  20mbar 

Injector size (Manual):   

504   

  704 

Injector size (Remote):  

494   

  NA* 

Number of Injectors:    

 

  1 

Gas Connection Size:   

8mm   

  8mm 

Weight: 

 

       See Packaging 

LPG PROPANE (G31) 

 

16/18 Standard 

Heat Input Max (gross): 

6.3 kW 

Heat Input Min (gross):  

5.3 kW 

Inlet Pressure:  

 

37 mbar    

Injector size:  

 

194 

Number of Injectors:    

Gas Connection Size:    

8mm 

Weight: 

 

See Packaging

 

NOTE: Both the 16” and 18” versions use the 
same burner. On the 18 “ version the ceramic 
fuel effect pieces are wider and will fill the extra 
space. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INSTALLATION INSTRUCTIONS - ALL VERSIONS 

* Not Available on this model 

Summary of Contents for ROMANCE

















Reviews: