manualshive.com logo in svg

Briggs & Stratton Victa, Assembly And Owner'S Manual

Share
Download
Briggs & Stratton Victa Assembly And Owner'S Manual Download Page 24

Not for 

Reproduction

21

Troubleshooting

If running difficulties continue, contact your closest VICTA Authorised Service    
Centre in Australia and New Zealand. Please look up and locate your local  
Authorised Service Centre on 

www.victa.com.au

 or contact Victa Lawncare 

Customer Service. Refer to the warranty card for the contact details. 

Problem

Possible cause

Remedy

Poor acceleration

Fuel filter clogged

Contact Service Centre

Fuel system clogged

Excessively low idle

Speed up idle/Contact Service 
Centre

Excessively lean carburettor 
setting 

Contact Service Centre

Clogged air filter

Clean filter

Air leakage

Loose carburettor

Contact Service Centre

Loose fuel pick up tube

Insert firmly/Contact Service 
Centre

Engine stops during operation

Switch is bumped

Keep hands clear of switch

Engine stops abruptly

Shorting of spark plug

Clean spark plug

Piston scored, ignition failure

Contact Service Centre

Miscellaneous

Fuel tank empty

Refuel

Carburettor or fuel tank clogged

Contact Service Centre

Engine is difficult to shut off

Overheated engine

Run at idle

Overheating or electrical fault

Overheated spark plug

Clean and adjust gap to 0.7mm 
(0.25")

Defective kill switch

Contact Service Centre

Poor contact of ground wire

Contact Service Centre

Unit main body

Loose trimmer head

Tighten firmly

Irregular vibration or trimmer 
head spins with engine idling

Broken clutch spring, bent main 
shaft

Contact Service Centre

Worn shaft bearings

Contact Service Centre

Loose gear head

Tighten bolt securely/Contact 
Service Centre

Bump head:

Line doesn't come out 
when head is bumped

Inappropriate winding 
of line.

Line inside bump head 
is nearly finished.

Open bump head and rewind 
the line ("Fitting trimmer line - 
bump head" on page 9)

Replace the residual line with 
the new line ("Fitting trimmer line 
- bump head" on page 9)

TROUBLE

SHOOTING

Summary of Contents for Victa





























Reviews:

No comments

Brands by name

Popular brands

Load more brands