Briggs & Stratton Victa Assembly And Owner'S Manual Download Page 22

Page: 22 / 28

Not for

Reproduction

Maintenance Chart

Refer to the following table for routine maintenance.

Always stop the engine before any maintenance is done on the unit.
When all parts have stopped rotating, remove the spark plug lead to
begin maintenance work.

Never repair cutting attachments by welding, straightening or custom
reworking of parts. This may result in product failure or serious injury.

Never attempt maintenance that is not outlined in this manual. All repair
work must be carried out by a VICTA Authorised Service Centre.

Features

Requirements

Bef

ore

ter finish

efuelling

Monthly

If damaged

As required

Trimmer

Visual inspection (leaks)

•

Throttle lever

Check operation

•

Throttle trigger
interlock

Check

•

Stop switch

Check

•

Fuel tank

Clean

•

Cutting Head Assy

Check & clean

•

Gearbox

Grease (straight shaft)

•

Air filter

Check

•

Clean

•

Replace (Depending on conditions)

•

Cowling

Clean

•

Cylinder fins

Clean

•

Spark plug

Clean & readjust gap

•

Nylon Line

Stock replacement

Cast Trimmer Head

Clean

Replacement

•

All accessible fasteners

Retighten

•

Muffler

Inspect

•

Inspect spark arresting screen

•

Clean or replace

•

Bump Head

Inspect

•

Summary of Contents for Victa





























Search results

Summary of Contents for Victa

Reviews:

Brands by name

Popular brands

Briggs & Stratton Victa, Assembly And Owner'S Manual

Search results

Summary of Contents for Victa

Reviews:

Brands by name

Popular brands