BridgeComSystems ComLink CS-540, Owner'S Manual

Page: 26 / 33

APPENDIX B: REMOTE PROGRAMMING QUICK REFERENCE
Each command below must be followed the ‘#’ symbol to execute. After you press ‘#’ and dekey, you’ll hear either a
success alert (four 1500 Hz tones) or a failure alert (four 500 Hz tones.) When you save and exit, you’ll hear a series of
tones then three 600 Hz tones to let you know it exited remote programming.
ENTER REMOTE MODE: EXIT WITHOUT SAVE:
1) Remote access PIN [N][N][N][N] 1) Command Prefix [9][8]
ADD USER: SAVE AND EXIT:
1) Command Prefix [0][1] 1) Command Prefix [9][9]
2) User Slot [N][N] 00 < NN < 63 REBOOT:
3) Tone/Code
[N][N][N]
001 < NNN < 162 1) Command Prefix
[5][5][5][5]
DELETE USER:
1) Command Prefix [0][2]
2) User Slot
[N][N]
00 < NN < 63
ACTIVATE USER:
1) Command Prefix [0][3]
2) User Slot
[N][N]
00 < NN < 63
DEACTIVATE USER:
1) Command Prefix [0][4]
2) User Slot
[N][N]
00 < NN < 63
MODIFY USER TX SQUELCH OPTION:
1) Command Prefix [0][5]
2) User Slot
[N][N]
00 < NN < 63
3) Tone/Code [N][N][N] 001 < NN < 162
MODIFY USER RX SQUELCH OPTION:
1) Command Prefix
[0][6]
2) User Slot [N][N] 00 < NN < 63
3) Tone/Code [N][N][N] 001 < NN < 162
MODIFY USER TX DCS SIGNAL POLARITY:
1) Command Prefix [0][7]
2) User Slot [N][N] 00 < NN < 63
3) Polarity
[N]
0 = inv; 1 = non
MODIFY USER RX DCS SIGNAL POLARITY:
1) Command Prefix [0][8]
2) User Slot
[N][N]
00 < NN < 63
3) Polarity [N] 0 = inv; 1 = non
MODIFY USER TX HOLD TIME:
1) Command Prefix
[0][9]
2) User Slot [N][N] 00 < NN < 63
3) Hold Time (ms)
[N][N][N][N]
0000 < NNNN< 9999
MODIFY USER TONE IN TAIL:
1) Command Prefix [1][0]
2) User Slot
[N][N]
00 < NN < 63
3) Tone in Tail
[N]
0 = No / 1 = Yes
MODIFY USER COURTESY TONE:
1) Command Prefix
[1][1]
2) User Slot [N][N] 00 < NN < 63
3) Courtesy Tone (Hz) [N] 0 = None, 1 = 500,
2 = 1000, 3 = 1500
MODIFY CHANNEL ID INTERVAL:
1) Command Prefix [1][2]
2) Interval (minutes)
[N][N][N]
000 < NNN < 999
MODIFY CHANNEL MORSE RATE:
1) Command Prefix [1][3]
2) Rate
[N]
0 = 11 WPM, 1 = 22 WPM
MODIFY CHANNEL TX TIMEOUT:
1) Command Prefix [1][4]
2) Timer (seconds)
[N][N][N]
000 < NNN < 999
MODIFY RX MODULE OUTPUT 1:
1) Command Prefix [1][5]
2) Position [N] 0-Low 1-High
MODIFY RX MODULE OUTPUT 2:
1) Command Prefix [1][6]
2) Position [N] 0-Low 1-High
26