BridgeComSystems ComLink CS-540, Owner'S Manual

Page: 16 / 33

ENTER REMOTE MODE:
ACTIVATE USER:
Field Digits Remarks
1) Command
[0][3]
2) User Slot
[N][N]
00 < NN < 63
Field Digits
1) Remote access PIN [N][N][N][N]
• The remote access PIN is preprogrammed
on a per channel basis. You must know it
before you begin.
• All users are active by default. This
command is used only to reactivate a user
that has been previously deactivated.
• Only the System Operator may access
remote programming mode.
DEACTIVATE USER: Deactivate an active user.
• The four-digit code “5555” is reserved for
the REBOOT command.
Field Digits Remarks
1) Command
[0][4]
2) User Slot
[N][N]
00 < NN < 63
• If you have successfully entered remote
programming mode, you’ll hear three 1500
Hz tones. If you weren’t successful, you
won’t hear any response.
• DEACTIVE USER is a good alternative to
DELETE USER when you want to
temporarily prevent a user from accessing
the repeater without deleting their profile.
ADD USER:
Field Digits Remarks
1) Command [0][1]
2) User Slot
[N][N]
00 < NN < 63
3) Tone/Code [N][N][N] 001 < NNN < 162
MODIFY USER TX SQUELCH OPTION:
Field Digits Remarks
1) Command [0][5]
2) User Slot [N][N] 00 < NN < 63
3) Tone/Code [N][N][N] 001 < NN < 162
• See “Appendix C” for a table of available
tones/codes and their corresponding index.
• If you attempt to add a user to a slot that
is already occupied by an existing user
(active or not), then this command will fail.
You must first delete the existing user and
then add a new one if you wish to add a
new user in that slot.
• CTCSS tones are numbered from 1-50 and
DCS codes are numbered from 51-162.
See “Appendix C:” for a complete table of
available tones/codes and their
corresponding index.
MODIFY USER RX SQUELCH OPTION:
• By default, the same tone/code will be
used for both the TX and RX squelch
options. After adding the user, you can
modify the TX and RX squelch options
individually by using the MODIFY TX
SQUELCH OPTION
or MODIFY RX SQUELCH
OPTION commands.
Field Digits Remarks
1) Command [0][6]
2) User Slot [N][N] 00 < NN < 63
3) Tone/Code [N][N][N] 001 < NN < 162
• CTCSS tones are numbered from 1-50 and
DCS codes are numbered from 51-162.
See “Appendix C” for a complete table of
available tones/codes and their
corresponding index.
DELETE USER:
Field Digits Remarks
1) Command
[0][2]
2) User Slot
[N][N]
00 < NN < 63
MODIFY USER TX DCS SIGNAL POLARITY:
• This command will delete the user’s profile
entirely and the slot will be considered
empty. If you want to temporarily disable
a user while preserving their profile, try
using the DEACTIVE USER command
instead.
Field Digits Remarks
1) Command [0][7]
2) User Slot [N][N] 00 < NN < 63
3) Polarity
[N]
0 = inverted
1 = non-inverted
• You can not delete the user in Slot 0
(System Operator) or Slot 1. These users
can only be deleted by using the PGM-540
programmer.
• This command will fail if the user is not
using a DCS Code as the squelch option.
16