manualshive.com logo in svg

Bridge Technologies VB440, User Manual

Share
Download
Bridge Technologies VB440 User Manual Download Page 8

On the

Software activation

screen, expand the IP-Probe menu and input both the software license, and

the software maintenance license, pressing

Add license

after each license. When all the licenses have

been accepted, press the

Activate

button. You can now access the regular probe UI by going straight to

the IP again.

To get back into the system admin dashboard, go to http://IP/admin/.

3.4

Graphical User Interface

The default GUI should look similar to the following picture. For more information, refer to chapter 4.

3.5

Configuring Ethernet settings

The VB440 comes with built in support for editing the network interface settings. To access the system

admin interface, point your browser to http://IP/admin/ and log in using the default system username

root

and the password

elvis

.

This is described in more detail in the

System Administration

part of the manual.

8

VB440 Studio Probe User’s Manual v6.0

© Bridge Technologies Co AS

Summary of Contents for VB440





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands