brevini Dana E Series Installation And Maintenance Manual Download | Manualshive

Page: 25 / 52

background image

SAFETY

25

Dana Incorporated

IMM-0017EN - Installation and Maintenance Manual

5.3.1.4 Lubricant

5.3.1.5 Ambient Conditions

WARNING

Extended, intensive contact with oils can lead to skin irritations.

Avoid extended contact with oil, and clean oil off skin thoroughly.

WARNING

Hot oil can cause scalding.

When changing oil, protect yourself against contacting hot oil.

DANGER

If the gear unit will be used in outdoor applications the gear unit must be prevented from rain snow and dust. Entering sub-
stances inside the gear unit from seals can damage the gear unit. Observe the safety instructions for outdoor use
EN12100:2010.

WARNING

Standard gearboxes are allowed to work in ambient temperatures b5 to +40ºC unless differently specified on the
nameplate. Using the gear unit out of this range can cause damage to the gear unit or environment. Over +40 ºC ambient
conditions the gear unit surface temp could be so high causing burns when touched.

«
...
23
24
25
26
27
...
»

Summary of Contents for Dana E Series





















































Reviews:

No comments

Related manuals for Dana E Series

Brand: BAFANG Pages: 12

EtherCAT BG 65 S

Brand: Ametek Pages: 38

950-1020 MOTOR KIT 8504048 REV 2 1297

Brand: TJERNLUND Pages: 2

Brand: Power Fist Pages: 40

Brand: REXROTH Pages: 86

Brand: Siemens Pages: 20

Brand: Siemens Pages: 26

Brand: Siemens Pages: 40

Brand: Siemens Pages: 87

Brand: Siemens Pages: 96

Brand: Siemens Pages: 116

Brand: Siemens Pages: 156

Brand: Siemens Pages: 252

SIMOTICS SD 1LE8 Series

Brand: Siemens Pages: 29

SIMOTICS M-1PH1

Brand: Siemens Pages: 8

Simotics SD 1LE7

Brand: Siemens Pages: 44

SIMOTICS S-1FT2

Brand: Siemens Pages: 102

SIMOTICS T-1FW4407-1KM81-1BC0-Z

Brand: Siemens Pages: 114

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands