B
C
D
E
Regolazione della lama di sx (vista dal posto di la-
voro).
6 - Allentare le 4 viti di fig.47 in maniera tale da rende-
re libero il movimento del gruppo colonne lama.
7a - Ruotare la vite di regolazione dell’angolo di fig.48
per mezzo di una chiave in senso:
ANTIORARIO per ottenere una modifica
dell’angolazione della lama per un taglio più corto (<
di 45°).
ORARIO: Per ottenere una modifica dell’angolazione
della lama per un taglio più lungo > a 45°.
Tali aggiustamenti consistono nel ruotare la vite di
regolazione di fig.48 una volta che essa si è appog-
giata contro il relativo fermo A o B di circa 1/4 o 1/2
giro al massimo.
8 - Controllare che l’angolazione della lama sia sta-
ta modificata correttamente. La giusta posizione si
ottiene quando il lato diagonale del calibro si appog-
gia esattamente per tutta la sua lunghezza contro il
corpo della lama e contemporaneamente un lato di-
ritto dl calibro è appoggiato contro la guida di
riscontro(fig.49)
9 - Una volta ottenuta la regolazione richiesta fissare
nuovamente le 4 viti di fermo del supporto
colonne.(fig.50)
Quindi procedere, se necessario con la regolazione
della lama di dx. Prima di tutto seguire i punti 4 - 5 e
6 sopra descritti e poi procedere alla regolazione
come spiegato qui sotto.
7b - Ruotare la vite di regolazione dell’angolo per
mezzo di una chiave in senso:
ORARIO: Per ottenere una modifica dell’angolazione
della lama per un taglio più corto (< a 45°).
ANTIORARIO: per ottenere una modifica
dell’angolazione della lama per un taglio più lungo
(> di 45°).
Tali aggiustamenti consistono nel ruotare la vite di
regolazione di fig.50 una volta che essa si è appog-
giata contro il relativo fermo A o B di circa 1/4 o 1/2
giro al massimo.
Per il controllo della modifica dell’angolazione della
lama che si è ottenuta vedere il punto 8. Alla fine
delle due operazioni di regolazione effettuare una
prova di taglio come specificato ai punti A e B di que-
sto paragrafo per verificare se si è ottenuto un risul-
tato di taglio soddisfacente altrimenti procedere nuo-
vamente ad un’altra regolazione.
Adjustment of the left (looking from the operator
working position)blade.
6 - Loose the four bolts of pict.47
7a - Turn the screw of pict. 48 by means of the proper
wrench.
COUNTERCLOCKWISE: To modify the cutting angle
to obtain a shorter cut (more than 45°).
CLOCKWISE: To modify the cutting angle to obtain a
longer cut (less than 45°)
These adjustment (pict. 48)consist in turning the
screw once it has reached the stop A or B, of about
1/4 or, maximum, half a turn.
8 - Check that the cutting angle of the saw blade has
been adjusted in the correct sense. The blade is in
perfect square when there is no space between one
caliber side and the fence nor between the diagonal
caliber side and the blade. (pict. 49)
9 - Once the adjustment is obtained thighten the four
bolts of pict.47
If it is necessary, to, adjust the right saw blade. First
repeating the points 4 - 5 and 6 here over described
and then follow hereunder instructions:
7 b - Turn the screw by mean of the proper wrench.
CLOCKWISE: To modify the cutting angle to obtain a
shorter cut (more than of 45°)
COUNTERCLOCKWISE: To modify the cutting angle
to obtain a longer cut (less than 45°).
These adjustment consist in turning the screw (pict.
50) once it has reached the stop A or B of about 1/4
or, maximum, half a turn.
To check if the blade angle adjustment has been
done properly see point 8.
After adjusting follow the instructions on page 12
points A and B to verify if this paragraph in order to
verify if the proper adjustment has been reached oth-
erwise repeat again the angle adjustment instruc-
tions to modify again the blade angle.
47
48
49
50
Summary of Contents for PRISMATIC E
