Breeze33 BZ3310WAC1 User Manual Download Page 5

4

IMPORTANT SAFETY INSTRUCTIONS

-Do not use means to accelerate the defrosting process or to clean, other than those

 

recommended by the manufacturer.
-The appliance shall be stored in a room without continuously operating ignition
sources (for example: open flames, an operating gas appliance) and ignition sourcesor
(for example:an operating electric heater) close to the appliance.
-Do not pierce or burn.
-Be aware that the refrigerants may not contain an odor.
-Compliance with national gas regulations shall be observed.
-Keep ventilation openings clear of obstruction.
-The appliance shall be stored so as to prevent mechanical damage from occurring.
-A warning that the appliance shall be stored in a well-ventilated area where the room
size corresponds to the room area as specified for operation.
-Any person who is involved with working on or breaking into a refrigerant circuit should
hold a current valid certificate from an industry-accredited assessment authority, which

 

authori

z

es their competence to handle refrigerants safely in accordance with an

industry recogni

z

ed assessment specification.

-Servicing shall only be performed as recommended by the equipment manufacturer.

 

Maintenance and repair requiring the assistance of other skilled personnel shall be
carried out under the supervision of the person competent in the use of flammable refrigerants.
-DO NOT modify the length of the power cord or use an extension cord to power the unit.
DO NOT share a single outlet with other electrical appliances. Improper power supply
can cause fire or electrical shock.
-Please follow the instruction carefully to handle, install, clear, service the air
conditioner to avoid any damage or hazard. Flammable Refrigerant R32 is used within
air conditioner. When maintaining or disposing the air conditioner, the refrigerant (R32
or R290) shall be recovered properly, shall not discharge to air directly.
-No any open fire or device like switch which may generate spark/arcing shall be
around air conditioner to avoid causing ignition of the flammable refrigerant used.
Please follow the instruction carefully to store or maintain the air conditioner to prevent

 

mechanical damage from occurring.
-Flammable refrigerant -R32 is used in air conditioner. Please follow the instruction
carefully to avoid any hazard.

WARNING: (

for using R290/R32 refrigerant only)

Caution: Risk of fire/
flammable materials

(Required for R32/R290 units only)

IMPORTANT NOTE:Read this manual 
carefully before installing or operating 
your new air conditioning unit. Make sure 
to save this manual for future reference.

Summary of Contents for BZ3310WAC1

































Reviews: