BRAYER BR4000, Instruction Manual

Page: 5 / 27

8 9 EN EN
• Before ironing check the recommended ironing
temperature indicated on the tag.
• If the item label is marked with the symbol , do not
iron the item.
• If there is no label on the clothes item, but you know
the type of fabric, refer to the following table to
determine the proper temperature.
Icons, type of fabric Icons Color of indicator
– nylon, acryl,
polyester
• Blue
– wool, polyester
blended fabric
•• Purple
– cotton, linen
••• Green
«Max» – denim max Red
– do not iron
- -
On – standby mode - Yellow
• This table is only valid for smooth materials.
• Fabrics of other types (crimped, raised, etc.) are best
ironed at low temperature.
• Sort items by ironing temperature first: synthetics
with synthetics, wool with wool, cotton with cotton.
• The soleplate (11) heats up faster than it cools down,
that’s why you should start ironing with synthetics,
then increase the temperature and iron silk and wool
items. Cotton and linen items should be ironed last.
• If an item is made of mixed fabrics, set the lowest ironing
temperature. For instance, if an item is made from
polyester and cotton, set the ironing temperature for
synthetics «•».
• If you cannot define the fabric structure, find a place that
is inconspicuous while wearing and select the ironing
temperature experimentally (always start with the lowest
temperature and raise it gradually until you get the
desired result).
• Corduroy and other fabrics that can become glossy
should be ironed backside.
DRY IRONING
Notes:
- each press of the TEMP button on the control panel
(6) is accompanied by a sound signal;
- the heating temperature of the sole (11) is indicated by
color indicators on the control / display panel (6).
Temperature and color chart
Yellow ON – Standby mode
Blue •
Purple ••
Green •••
Red Max
• Place the iron on the base (9) on a flat and steady
surface.
• Insert the power plug into the mains socket, the
yellow indicator « » will light up on the panel (6) and
the iron will switch on in the standby mode.
• Set the steam supply knob (3) to the position « »
(the steam supply is off) (pic. 1).
• Press the button «TEMP» on the control panel (6)
to set the required temperature «•», «••», «•••» or
«max» (see the table of temperature and indicator
colors). The flashing of a colored indicator on the
control/indication panel (6) will confirm the set
temperature.
• When the iron soleplate (11) reaches the set
temperature, the temperature indicator on the control/
indication panel (6) will glow constantly, and you can
start ironing.
• After you finish using the iron, press the button
«TEMP» on the control panel (6) to switch the
standby mode « » on, the indicator will glow yellow
(see the table).
• Disconnect the power plug from the mains socket
and wait until the iron soleplate (11) cools down
completely.
Note: when switching the unit on for the first time,
foreign smell can appear. It is normal.
STEAM IRONING
The iron is equipped with anti-drip valve that stops water
supply, if the soleplate (11) temperature is too low, it
prevents dripping from the soleplate (11) openings.
Steam ironing is possible only at the temperature «•••» or
«max».
• Place the iron on its base (9).
• Insert the power plug into the mains socket, the yellow
indicator « » will light up on the panel (6) and the iron
will switch on in the standby mode.
• Make sure that there is enough water in the water tank
(10).
• Press the button «TEMP» on the control panel (6) to set
the required temperature «•••» or «max». The flashing of
a colored indicator on the control panel (6) will confirm
the set temperature (see the table of temperature and
indicator colors).
• When the iron soleplate (11) reaches the set
temperature, the temperature indicator on the control/
indication panel (6) will glow constantly, and you can start
ironing.
• Set the continuous steam supply regulator (3) to the
position « » (pic. 1), steam will be released from the
soleplate (11) openings only in horizontal position. To
stop the steam supply, put the iron vertically or set the
regulator (3) to the position « » (steam supply off) (pic.
1).
• After you finish using the iron, set the continuous
steam supply regulator (3) to the position « » (steam
supply off) (pic. 1), press the button «TEMP» on the
control panel (6) to switch the standby mode « »