6
7
en
en
USING THE MULTISTYLER
Use the multistyler for both long hair and hair of
middle length.
• Place the multistyler on a flat steady heat-resistant
surface. Make sure that the operating elements
and the outer surfaces do not touch fusible and
inflammable objects.
•
Use the unit on healthy undyed and unpermed hair.
•
If your hair is dyed or permed, use the multistyler
rarely.
•
Before styling, wash your hair with shampoo, wipe it
with a towel, dry with a hairdryer and comb.
SETTING THE ATTACHMENTS
Before installing the attachments make sure that the
operation mode switch (7) is set to the position «0»,
and the plug is not inserted into the socket.
•
Turn the attachment lock (2) until the symbols «
p
»
and «▼» match.
•
Install the hair crimper or the tongs attachment
into the unit body (1) matching the ledges on the
attachment with the grooves in the attachment lock
(2). Turn the attachment lock (2) counterclockwise
until the symbols «▼» match. Make sure that the
installed attachment is fixed properly.
•
To remove the attachment, switch the unit off by
setting the operation mode switch (7) to the position
«0», unplug the unit and wait until the attachment
cools down. Turn the attachment lock (2) clockwise
and remove the attachment.
HAIR CRIMPER ATTACHMENT
• Put the multistyler on a flat steady and heat-resistant
surface.
•
Insert the power plug into the mains socket.
•
Set the required operation mode with the switch (7),
the pilot light (6) will light up:
- «0» — the multistyler is switched off
- «1» — low heating temperature
- «2» — high heating temperature
•
Set the switch (3) to the required position for hair
straightening or hair crimping.
•
divide hair into locks about 4-5 cm wide.
•
Press the handle (5), place a hair lock between the
heating plates (4), release the handle (5).
WARNING: do not hold the heating plate at one area
of the hair lock for longer than 2-5 seconds.
•
If you are using the heating plates (4) for hair
straightening, slide them throughout the hair lock
length.
•
If you are using the hair crimping function, wait a
little, then press on the handle (5) and move the
plates (4) to another part of the hair lock.
•
Straighten/style all hair locks.
• Cool your hair down before final styling or applying
hair spray.
•
Avoid contact of heated surfaces of the attachment
with your face, neck and other parts of your body.
• After you finish using the unit, set the operation mode
switch (7) to the position «0», and unplug the unit.
Let the unit cool down.
•
Notes:
-
when switching the unit on for the first time, a
smell from the heating element can appear, this is
normal and it is not covered by warranty.
- always switch the unit off and unplug it when
you’re not using it.
CURLING TONGS ATTACHMENT
•
Install the tongs attachment and make sure that it is
fixed properly.
• Put the unit on the base (9) on a flat heat-resistant
surface.
•
Insert the power plug into the mains socket.
•
Switch the unit on by setting the operation mode
switch to the corresponding position «1/2», the pilot
light (6) will light up.
• Wait until the operating surface (10) of the
attachment heats up.
•
Take a hair lock with the free hand.
•
Press the clamp handle (12) with the other hand,
place the end of the hair lock on the operating
surface (10) and release the clamp handle (12).
Holding onto the tip (11) and the unit body, wind the
hair lock around the operating surface (10).
• Wait for a while, then press the clamp handle (12)
and release the hair lock.
•
Repeat this procedure on the rest of your hair.
NOTES:
-
when using the unit for the first time, a foreign
smell from the heating element can appear — this
is normal and it is not covered by warranty.
- avoid contact of hot surfaces of the attachment
with your face, neck and other parts of your body
during the unit operation.
- during breaks in operation, place the unit on the
base (9) on a flat heat-resistant surface.
- do not comb the hair right after curling it, let it
cool down, hair spray should be applied after hair
curling.
• After you finish using the unit, switch it off by setting
the operation mode switch (7) to the position «0»,
and unplug the unit.
• Put the unit on the base (9) on a flat heat-resistant
surface and let it cool down completely.
SPIRAL TONGS ATTACHMENT
•
Install the spiral tongs attachment (13) on the tongs
operating surface (10).
CLEANING AND MAINTENANCE
•
Before cleaning unplug the unit and let it cool down
completely.
•
do not immerse the unit, power cord and power plug
of the unit into water or any other liquids.
•
do not use detergents, abrasives or any solvents to
clean the unit.
•
Clean the unit body and the attachments with a soft,
slightly damp cloth, and then wipe it dry.
STORAGE
•
Let the unit cool down completely and clean it before
taking away for storage.
Summary of Contents for BR3360
Page 21: ...brayer su ...
