10
EN
the Auger (4). Having dealt with it, reinstall the Feeding
Chute/Lid (2-3) to continue using the Juicer.
•
Once the juice container (13) has filled up, turn the
Juicer off and pour the juice into a suitable container,
place the juice container (13) under the juice spout (9).
Note:
slowly pour juice out of the Juice Container (13) -
the froth separator will remove any foam.
• Remove the froth separator, wash the Juice Container
(13), reinstall the froth separator (fig. 8).
Note:
for your convenience, place an appropriately-
sized bag into the pulp container (14) to remove the pulp
together with the bag.
•
Keep the juice container (14) full, turn off the juicer and
remove the juice from the container (14).
•
Once you finish using the Juicer, turn it off by setting
the power (11) to «OFF», and unplug it from the mains.
OVERHEATING PROTECTION
• Exceeding the operating temperature will trigger the
overheating protection and the Juicer will turn off.
•
Should the Juicer turn off on its own, set the power (11)
to «OFF» and unplug it from the mains.
• Depending on the room temperature, the electric motor
can take from 20 to 50 minutes to cool down, once it
has cooled down, plug it into the mains and turn the
Juicer on.
• Should the Juicer fail to turn on, wait for some time, if
nothing changes this might indicate another defect. In
this case, please, contact an authorized service center.
• Do not exceed the recommended operation time.
CLEANING AND CARE
• Perform cleaning of the Juicer after each use.
•
Turn off the Juicer and unplug it from the mains
before cleaning.
• Remove the pusher (1) from the feeding chute (2).
• Turn the feeding chute/lid (2-3) counterclockwise and
remove them.
• Remove the Auger (4), Mesh Filter (5), and Separator
(6) from the Juice Bowl (7).
• Rotate the Juice Bowl (7) in the counter-clockwise
direction and remove it from the Motor Unit (10).
• Wash the removed parts (2-3, 4, 5, 6, 7), the juice
cup (13), the pulp container (14) with warm water and
a neutral detergent, then rinse and dry.
• For your convenience, remove the froth separator
from the Juice Container (13), wash the Juice
Container (13), and reinstall the froth separator back
(fig. 8).
• Extract the Silicone Seal (12), located inside the
Juice Bowl (7), clean and wash the pulp canal.
• Reinstall the Silicone Seal (12) back inside the Juice
Bowl (7) (fig. 1).
• Use the brush (15) to clean the Mesh Filter (5) and
other hard-to-reach places.
• Do not wash the removable parts of the Juicer in a
dishwasher.
Summary of Contents for BR1703
