background image

800-350-8739 

1

Brave

 

EZ Split 15 Quick Reference Guide

 

 

1

Safety Instructions

 

Do not attempt to assemble, operate, or maintain the log splitter 
unless you read and understand the instructions, precautions, and 
warnings in this manual. See pages 4-9. 

 

2

Assembly Instructions

 

Follow the steps listed and assemble your EZ Split 15 log splitter. 
See pages 10-14. 

 

3

Initial Start-Up Procedure

 

These instructions include the proper fluids to fill the hydraulic tank, 
engine crankcase, and engine fuel tank. Follow the instructions 
exactly. See pages 15-16. 

 

4

Towing

 

Read and understand completely before towing your EZ Split 15. 
See pages 17. 

 

5

Operation

 

Read and understand completely before using your EZ Split 15 to split 
wood. See pages 18-23. 

 

6

Inspection and Maintenance

 

Follow these instructions for inspection and maintenance of your 
EZ Split 15. See pages 23-28. 

 

7

Serial Number

 

Write the serial number and date of purchase in the space available 
at the bottom of this page. 

 

8

Warranty Card

 

Fill   out   and   return   the   warranty   card   to   Brave   Products,   Inc. 
See page 41. 

 

Serial Number   

 

Date-of-Purchase    

 

 

 

Please enter the serial number and purchase date 
of your log splitter in the space provided. Keep this 
manual for future reference. 

 

 
 
 

NOTE:  

Brave reserves the right to make technical changes for product improvement. 

This manual may contain illustrations and photographs, for demonstration 
purposes, which slightly deviate from the actual product design. 

Summary of Contents for PCLS1513

















































Reviews: