background image

Page 9

Inspect lift for wear, damage or any abnormal 
condition

Inspect lift for rattles

Correct as needed.

Correct as needed.  

Outer barrier latch pivot (2)

Upper/lower fold arm telescoping area (2)

Platform pivot pin (2) 
 
Platform fold axles (2)

Inner roll stop (

IB

) lever (2)

Inner roll stop (

IB

) lever slot (2)

Rotating pivot slide arm pivot pins (2) 

Parallel arm pivot pins (8)

Handrail pivot pins (2)

Hydraulic cylinder bushings (8)

Inspect Lift-Tite

 latch rollers for wear or damage, 

positive securement and proper operation (2) 

Inspect outboard barrier slide link for positive 
securement and detached or missing extension 
spring

Inspect outboard barrier raised and ground 
detect magnetic sensors and magnet for positive 
securement

Inspect IB inner roll stop (

IB

) rasied magnetic 

sensor and magnet for damage and positive 
securement

Inspect rotory incoder and associated components 
for wear or damge and positive securement

Inspect inner roll stop (

IB

) for:

• Wear or damage
• Proper operation.  Rollstop should just rest on top  

surface of the base plate.

• Positive securement (both ends)

Inspect handrail components for wear or damage, 
and for proper operation

Inspect microswitches for securement and proper 
adjustment.
 

 

Make sure lift operates smoothly

Apply Light Oil - See Lubrication Diagram

Apply Light Grease - See Lubrication Diagram

Apply Light Oil - See Lubrication Diagram

Apply Light Oil - See Lubrication Diagram

Apply Light Oil - See Lubrication Diagram

Apply Light Oil - See Lubrication Diagram
 
Apply Light Oil - See Lubrication Diagram

Apply Light Oil - See Lubrication Diagram

Apply Light Oil - See Lubrication Diagram

Apply Light Oil 

Correct, replace defective parts and/or relubricate.

Resecure, replace or correct as needed.  See Lift 
Exploded View.

Resecure, replace or correct as needed.  See 
Switch and Sensor Location Illustration.

Resecure, replace or correct as needed.  See 
Switch and Sensor Location Illustration.

Resecure, replace or correct as needed.  See 
Switch and Sensor Location Illustration.

Resecure, replace or correct as needed.  See 
Platform Angle Instructions and Microswitch Ad-
justment Instructions.

Replace defective parts. 
 

Resecure, replace or adjust as needed.  See 
Microswitch Adjustment Instructions.

Realign towers and vertical arms.  Lubricate or 
correct as needed.

Perform all procedures listed in previous section also

750 

Cycles

1500 

Cycles

Maintenance and Lubrication Schedule

Summary of Contents for NCL Century 04 Series



























Reviews: