background image

Page 52

AUXILIARY POWER SUPPLY / BELOW FLOOR OBSTRUCTIONS

Note:  

The technical information 

provided on pages 52-55 of this 
manual is service related.

  

If you 

are having an electrical tie-down, 
power seat or other auxiliary 
electrical device installed in your 
Entervan, this information should 
be supplied to the technician.  
Otherwise, disregard this section.

Auxiliary Power Supply:  Do not

 

connect auxiliary devices directly 
to the vehicle battery.  Doing so 

may result in damage to electri-
cal system and/or electronic 
components

.

Two fuse blocks are provided 
as an auxiliary power source for 
dealer-installed auxiliary electri-
cal device(s).  Fuse block details 
and speci

fi

cations are provided 

on page 53.  The fuse blocks are 
located in the bottom of the center 
dash console.

Below Floor Obstructions:  

When installing aftermarket equip-
ment in an Entervan, obstructions 
below the 

fl

oor must be avoided.  

Obstructions include wiring, fuel 
system, brake lines, etc.  Installers 
must be aware of these obstruc-
tions.

CAUTION

Do not connect
auxiliary devices to
vehicle battery.  Doing
so may result in dam-
age to electrical sys-
tem and/or electronic 
components.

WARNING

Risk of electrical 

fi

re!  

Install and electrically 
terminate auxiliary 
electrical device as 
speci

fi

ed by device 

manufacturer.

Refer to the illustration on page 55 
to avoid contacting or damaging 
vital components under the 

fl

oor.  

Summary of Contents for 2008 & Up Chrysler Foldout Entervan































































Reviews: