Brannan DT-8835 User Manual Download Page 9

Page: 9 / 16

InfraRed Thermometer User Manual

Switching °C/°F, Lock ON/OFF and Set Alarm

°C/°F

LOCK ON/OFF

Laser / Backlight

SET ALARM

MODE

Down

1-°C/°F
2-LOCK ON/OFF
3- et Alarm

•Select the temperature units (°C or °F) by using the

switch.

•To lock the unit on for continuous measurement, slide the middle

switch

right. If the trigger is pulled while the unit

is locked on, the laser and backlight will be turned on if they have

been activated. When the unit is locked on, the backlight and laser
will remain on unless it is turned off using the “

“

button on the keypad.

•To activate the alarms, please slide the botto switch

right.

•To set values for the High Alarm (HAL), Low Alarm (LAL) and Emissivity

(EMS), firstly active the display by pulling the trigger or pressing the
“

“ button, then press the “

“ button until the appropriate

code appears in the lower left corner of the display, press the “

“

and “

“ buttons to adjust the desired values.

1
2
3

Summary of Contents for DT-8835

















Search results

Summary of Contents for DT-8835

Reviews:

Related manuals for DT-8835

Brands by name

Popular brands

Brannan DT-8835, User Manual

Search results

Summary of Contents for DT-8835

Reviews:

Related manuals for DT-8835

Brands by name

Popular brands