39. Tone Out
:
Output of the Stripper.
40. Output 1-4 (40-43)
:
Outputs of the
Distributor/ Reshaper.
44. Input A
:
Rear panel time code input.
22.
Drop Frame
LED
:
On solid for drop
frame code; blinks mostly on for miss-
ing DF flag (bit 10); blinks mostly off
for false DF flag; off for non-drop.
23.
Video Code
LED
:
On solid if code is
synchronous and in phase with video;
blinks mostly on if code is out of
phase; blinks mostly off if code is drift-
ing; off if no video is present.
Stripper
24.
Source Select:
Selects the input of the
Stripper: Code / Video / AC Mains.
25.
Output Level:
Adjusts the Stripperʼs
output level from full off to +12dbU
26.
Output Waveform:
Determines the
waveform of the stripped tone: Square
wave / Sine wave.
16.
Reader (8 digit display):
Reads
time code, user bits or video phase;
identifies the error type and the faulty
address.
17.
Counter (4 digit display):
Reads the
frame rate (fr/sec) of the incoming time
code or the frequency (hz) of Tone in or
Tone out.
18.
Fr/Sec
LED
:
On when 4 digit display
counts frame rate.
19.
Hz
LED
:
On when 4 digit display
counts frequency.
20.
ASCII
LED
:
On when ASCII flags are
set. On means User Bits are ASCII;
off ,User Bits are Hex.
21.
Color Frame
LED
:
On when Color flag
is set (bit 11 ); off when flag is not set.
35. Dipswitches
:
Future upgrades - pg 9
36. Serial Port
:
DB-9M for RS-232 I/O.
37. Parallel Port
:
DB-25F
for Centronics
printer output.
38. Relay out / in
:
TRS
1/4” for remote
“Good Code” LED or extʼl trigger input.
INPUT B
OUTPUT 5
TONE STRIPPER
DISTRIBUTOR / RESHAPER
2
3
4
5
1
I_]dWb?d
=eeZ9eZ[
SOURCE
SELECT
OUTPUT
LEVEL
OUTPUT
WAVEFORM
IH#'+
!
J?C;9E:;
:?IJH?F7BOP;H
"2!).34/2-
%,%#42/.)#3).#
ICFJ;
(+¦i
IgkWh[
'¦i
;8K
+&¦i
7
H[Wh
8
<hedj
9eZ[
L_Z[e
CW_di
IgkWh[
I_d[
INPUT
SELECT
OUTPUT
RISE TIME
<hedjFWd[b
OUTPUT LEVEL
>h
C_d
I[Y
<h
CODE ANALYZER
>p
9ebeh<h$
:hef<h$
L_Z[e9eZ[
%<h[gk[dYo
9eZ[
L_Z£
Jed[
_d
Jed[
ekj
7I9??
9eZ[
<hWc[HWj[
<h%I[Y
H;7:;
H
9EKDJ;
H
E\\
Ki[h
Ed
8;;F;H
H;I;J
POWER
AUX I/O
INPUT
"
22 23
17
3
5
6
15
18 19
24
26
25
1
2
4
7
8
9
10
11
14
16
20
21
13
12
27
115 Vac
1 2 3 4 5 6 7 8
Loop
Input
Input
Loop
75
7
Off
VIDEO REFERENCE
Iso
Grnd
Ground
Lift
Ã>Ìi`
ÀÕ`i`
INPUT A
OUTPUT 1
OUTPUT 2
OUTPUT 3
OUTPUT 4
TONE OUT
J
I
H
RELAY
OUT/IN
VID OUT
COLOR ID
ANALYZER
XLR Pins:
1=G / 2=H / 3=L
Fuse, Slo-blo:
T 200mA @ 115VAC
T 100mA @ 230VAC
(Optional)
Parallel Serial
Termination
42
41
43
39
40
44
28
30
29
34
35
36
38
37
33
32
31
Rear Panel
28. Voltage Selector & Fuse drawer:
Selects 115VAC or 230VAC & holds
the main fuse and a spare.
29. Power In
:
IEC 320 power inlet.
30. Ground Lift Switch
:
Isolates chas-
sis ground from signal ground.
Aux I/O
1. Input B:
Auxiliary time code input, for
easy front panel access.
2. Output 5
:
Auxiliary time code output,
for easy front panel access.
Input Section
3. Input Select:
This switch determines
which input is active (front or rear).
4. Signal In
LED
:
Lights up when signal
is present at the selected input. Any
signal above -30db lights this
LED
.
5. Good Code
LED
:
Lights up when
valid code is present at the selected
input; blinks off momentarily if a
“Fatal” time code error is detected.
Power
27.
Power Switch:
Turns power on or off
Distributor
6.
Rise Time Switch:
Changes the
waveform of all 5 reshaped time code
outputs:
SMPTE
= 25µsec, square wave
= 1µsec and
EBU
= 50 µsec.
7. Output Level (7-11)
:
Adjusts the level
of each reshaped output individually
from full off to +12dbU.
Analyzer
12. Reset Switch:
Push button to reset
SR-15+ or clear displays.
13. Beeper switch:
turns beeper off.
14. Reader Select:
Selects the mode of
the 8 digit display: Time code/ User
bits/ Video ø.
15.
Counter Select:
Selects the input and
the mode of the 4 digit display : Code
/ Tone in / Tone out.
31. Color ID In & Loop
:
Input & loop for
color field ID pulse.
32. Termination
:
75Ω for video in & loop.
33. Video Reference In & Loop:
BNC
jacks for video reference.
34. Video Out (optional):
Report output.
