background image

 

25

Maintenance Continued- 

 

Regular inspection and maintenance of the water heater and vent-air intake 
system will help to insure safe and reliable operation. 
1.  Annually check the operation of the thermostat. 
2.  The flow of combustion and ventilation air

 MUST NOT 

be restricted.  Clear 

the combustion air openings of any dirt, dust, or other restrictions.

  

3. 

At all times keep the water heater area clear and free from combustible 
materials, gasoline and other flammable vapors and liquids. 

4.  Bi-annually conduct a visual check of the main and pilot burner flames to 

determine that they are burning properly.  See Burner Flame Check 
section.

 

 5.  Annually remove the inner door and main burner assembly to clean orifices 

and related parts of any dirt or other foreign material.  Inspect the burner 
ports for obstructions or debris and clean with a wire brush as needed.  
Wire brush and/or vacuum clean the combustion chamber as needed to 
remove scale deposits and debris.  

NOTE:

  It is imperative for proper 

operation of the water heater that the inner door be replaced in the original 
location. 

 

6. 

At least once a year, check the combination temperature and pressure relief 
valve to insure that the valve has not become encrusted with lime.  Lift the 
lever at the lever at the top of the valve several times until the valve seats 
properly without leaking and operates freely.

 

 7. 

Monthly drain off a gallon of water to remove silt and sediment. 

 

8. 

If the combination temperature and pressure relief valve on the appliance 
discharges periodically, this may be due to thermal expansion in a closed 
water supply system.  Contact the water supplier or local plumbing 
inspector on how to correct this situation.  Do not plug the combination 
temperature and pressure relief valve outlet. 

9.  A combination sacrificial anode rod/hot water outlet nipple has been 

installed to extend tank life.  The anode rod should be inspected 
periodically and replaced when necessary to prolong tank life.  Water 
conditions in your area will influence the time interval for inspection and 
replacement of the anode rod

.

 

 

WARNING 

The ventilation air system may be 

HOT

 

WARNING 

Do not run out of propane gas.  Damage to the water heater may occur. 

 

WARNING 

When lifting the lever of the combination temperature and 
pressure relief valve, hot water will be released under pressure.  
Be careful that any released water does not result in bodily injury 
or property damage.

 

 

WARNING 

THIS WATER MAY BE HOT

 . 

Summary of Contents for RG2DVMH30T6X-264





























Reviews: