background image

 

14

Installation (Water connections) continued- 
 

 

 

 

This water heater can deliver scalding temperature water at any faucet in the 
system.  Be careful whenever using hot water to avoid scalding injury.  Certain 
appliances such as dishwashers and automatic clothes washers may require 
increased temperature water.  By setting the thermostat on this water heater to 
obtain the increased temperature water required by these appliances, the 
potential for scald injury increases.  To protect against injury, you should install 
an ASSE approved mixing valve in the water system.  This valve will reduce 
point of discharge temperature by mixing cold and hot water in branch supply 
lines.  Such valves are available from the manufacturer of this water heater or a 
local plumbing supplier.  Please consult with a plumbing professional. 

 

 

 
 
 
 
 
 
 
 
 
 
 
 

 

WARNING 

Hydrogen gas can be produced in an operating water heater that has not had 
water drawn from the tank for a long period of time (generally two weeks or 
more).  Hydrogen gas is extremely flammable.  To prevent the possibility of 
injury under these conditions, we recommend the hot water faucet to be open 
for several minutes at the kitchen sink before you use any electrical appliance, 
which is connected to the hot water system.  If hydrogen is present, there will be 
an unusual sound such as air escaping through the pipes as hot water begins to 
flow.  Do not smoke or have open flame near the faucet at the time it is open. 

APPROXIMATE TIME/TEMPERATURE RELATIONSHIPS IN SCALDS 

120°F 

(49°C)

 

More than 5 minutes 

125°F 

(52°C)

 

1½ to 2 minutes 

130°F 

(54°C)

 

About 30 seconds 

135°F 

(57°C)

 

About 10 seconds 

140°F 

(60°C)

 

Less than 5 seconds 

145°F (

63°C

Less than 3 seconds 

150°F 

(66°C)

 

About 1½ seconds 

155°F 

(68°C)

 

About 1 second 

can cause severe burns 

are at highest risk of being

Children, disabled and elderly

instantly or death from scalds.

Water temperature over 125°F 

Feel water before bathing or

before setting temperature

available.

showering.

Temperature limiting valves are

Review this instruction manual

at water heater.

scalded.

Summary of Contents for RG2DVMH30T6X-264





























Reviews: