BPC instruments uFlow Operation And Maintenance Manual Download Page 40 | Manualshive

Page: 40 / 47

background image

35

Load Data

The Load Data page allows the user to load data from a specific time interval, and to generate
a report of it. The report contains experiment data for each reactor/line.

System

This page contains general information related to the software version, Data Logger hardware
and contact details.

D

ETAILED GUIDE FOR EACH PAGE

In each page it is possible to find additional menus by right clicking in different areas. Not all
the functions shown in these menus are activated in this application, and only the ones that are
useful for experiments with the µFlow Gas Meter are explained here.

«
...
38
39
40
41
42
...
»

Summary of Contents for uFlow
















































Reviews:

No comments

Related manuals for uFlow

Brand: Omicron Lab Pages: 33

Brand: Omicron Lab Pages: 21

Brand: Omicron Lab Pages: 22

Brand: Vectornav Pages: 114

Brand: QuadTech Pages: 76

Brand: PCB Piezotronics Pages: 11

Brand: LaserLine Pages: 11

Brand: Hanna Instruments Pages: 2

American AL-1000

Brand: Badger Meter Pages: 16

Brand: Velleman Pages: 32

Brand: LAUMAS Pages: 12

Brand: Roland Pages: 32

Brand: Barco Pages: 33

Brand: Hanna Instruments Pages: 2

Brand: Hantek Pages: 40

Brand: Opsytec Pages: 37

Brand: TE Connectivity Pages: 5

Brand: Seli Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands