background image

4     Ethernet Interface Adapter User’s Guide 

Check 05h

 

NVRAM and RAM problem 

 

Check 0Dh

 

MAC, NVRAM and RAM problem 

Check 06h

 

NVRAM and ROM problem 

 

Check 0Eh

 

MAC, NVRAM and ROM problem 

Check 07h

 

NVRAM, RAM and ROM 
problem  

 

Check 0Fh

 

MAC, NVRAM, ROM and RAM 

Check 08h

 

MAC problem 

  

Displaying the Ethernet Interface Main Menu 

If the

 Poweron Connect

 mode is 

Off

 (see page 8) at the conclusion 

of the startup diagnostics, you can press any key to enter the 
setup menu.  

 

Note that the Main Menu is accessible only when the 
terminal is disconnected from the host. 

If the 

Poweron Connect

 mode is 

On

, the card will automatically try 

to connect to the host. 

 

- MAIN MENU - 

Status > Disconnected from Host 
Host IP Address > XXX.XXX.XXX.XXX 
1.     Setup Menu 
 2.     Connect to Host 
 3.     Ping 
 4.     Hardware Information 
    --------------------------   
 9.     Exit Main Menu 

As shown in the illustration above, the Main Menu provides 
the following functions: 

◊ 

Selection 

1

 (Setup Menu) allows you to configure the 

Ethernet interface.  

Summary of Contents for Ethernet Interface Adapter



















Reviews: