background image

2

The wiring terminals and RF Address Code setting DIP switches are located on the rear of the 
Receiver.

Receiver Wiring Terminals

Terminal Name

Function

N

Neutral input 230VAC/50Hz

L

Live input 230VAC/50Hz

1: COM

Switch common terminal

2: NO

Normal open (Volt-Free Contact)

3: NC

Normal close (Volt-Free Contact)

Direct Control Boiler

 

Notes:

 Receiver unit should have a permanent 230V AC main supply

Combi Boiler

Notes:

    • Receiver unit should have a permanent 230V AC main supply 

• If the boiler has two terminals for the thermostat, remove the link from the boiler

Control Unit Jumper Settings

Changes to the jumper settings should only be made by the Engineer carrying out the installation 
or other qualified person.

The installer should select the jumper positions required if changes need to be made to the factory 
default settings. These jumpers are found on the rear of the Control Unit.

Jumpers

Description

Address code

5 DIP switch levers for 5 bits address code for 
RF communication (All jumpers default are closed)

Span

3x1 pins jumper for +/-0.5°C or 1.0°C 
(factory default setting) selection.
It is used to define the system to run at +/-0.5°C or 1.0°C 
difference to the set temperature

Notes :

   The 

Reset 

button must be pressed after changing jumper positions. 

The Reset button is accessible behind the small hinged door on the front right hand side of the Control Unit.

RECEIVER

N.0. COM L N

N
L

BOILER

Live Feed

L

N

E

MAINS
FEED

N

L

SL

Thermostat (Remove link)

Green/Yellow

Blue

Brown

Brown

Brown

Brown

Blue

RECEIVER

N.0. COM L N

N
L

BOILER

Live Feed

N

E

L

N

E

MAINS
FEED

Yellow

Blue

Brown

Brown

Brown

Blue

Summary of Contents for TPSRF31







Reviews: