manualshive.com logo in svg

Boss TGS 1100, Installation & Owner'S Manual

Share
Download
Boss TGS 1100 Installation & Owner'S Manual Download Page 17

RT3 Attachment Removal Procedure 

17 

RT3 Attachment 
Removal Procedure 

 

 

 

 

In order to prevent injury or damage to the 
product, the spreader must be completely empty 
when attaching or detaching it from the vehicle. 

 

 

 

 

Keep hands, feet, and clothing away from 
attachment points. 

 
1.  The In-Cab Controller must be turned 

OFF before proceeding. Back the truck 
into position. 

 

2.  Loosen Ratchet Straps (5). 

 

3.  Loosen Stabilizer Arms (3) & (4). 

 

4.  Unplug Spreader Side Harness from 

Vehicle Side Harness and install both 
the vehicle and spreader side weather 
caps. 

 

5.  Rotate the release lever clockwise to the 

“OFF” position

, refer to Figure 11. 

 
 
 

 

Figure 11.

 Lever Rotation 

G10393

 

 

6.  Push forward on the spreader to release 

the Upper Pin. 

 

7.  Rotate spreader to ground. 

 

8.  Grip spreader firmly, step on Leg 

Assembly and rotate spreader off Lower 
Pin, refer to Figure 12. 

 

9.  Roll spreader to storage area.

 

 

Figure 12.

 RT3 Attachment Removal Procedure

 

G10394 

Summary of Contents for TGS 1100




























Reviews:

No comments

Brands by name

Popular brands

Load more brands