Boss RC-600, Parameter Manual, Page: 39 / 48

39
Input FX/Track FX List
VOCODER
Vocoder sound that uses the audio input to modulate the sound of the track you
specify.
Parameter Value
(Bold: default)
Explanation
CARRIER
MIC1, MIC2, INST1-L,
INST1-R, INST2-L,
INST2-R,
TRACK1 –6
Sets the input or track (TRACK
1–6) that will be used as the basis
(carrier) of the vocoder sound.
* If the specified track is empty,
you won’t hear the vocoder.
TONE -50– 0 –+50
Adjusts the tonal character of the
vocoder part.
ATTACK 0–
50
–100 Sets the attack of the sound.
MOD SENS
-50– 0 –+50
Sets the sensitivity by which
the audio input will control the
modulation.
BALANCE 0– 50 –100
Adjusts the volume balance
between the direct sound and the
vocoder sound.
OSC VOC (M)
Creates a vocoder sound based on the MIDI note messages received.
Parameter Value
(Bold: default)
Explanation
CARRIER
SAW
,
VINTAGE SAW,
DETUNE SAW,
SQUARE, RECT Selects the carrier waveform (the
basic sound).
TONE -50– 0 –+50
Adjusts the tonal character of the
vocoder part.
ATTACK 0– 50 –100 Sets the attack of the sound.
OCTAVE
-2OCT, -1OCT, 0 ,
+1OCT
Sets the pitch of the sound.
MOD SENS -50–
0
–+50
Adjusts the sensitivity by which
the audio input will control the
modulation.
RELEASE 0–
50
–100
Sets the decay time (release time)
for sound initiated by a note
message.
BALANCE 0–
50
–100
Adjusts the volume balance
between the direct sound and the
vocoder sound.
OSC BOT
Plays the oscillator to match the value in the “NOTE” parameter. This plays melodies
and other phrases in combination with the sequencer.
Parameter Value
(Bold: default)
Explanation
OSC
SAW ,
VINTAGE SAW,
DETUNE SAW,
SQUARE, RECT
Selects the oscillator waveform.
TONE -50– 0 –+50
Adjusts the tonal character of the
oscillator.
ATTACK 0– 50 –100 Sets the attack of the sound.
NOTE
2
C1–
C2
–G9
Sets the note used to make the
oscillator sound.
MOD SENS
-50– 0 –+50
Sets the sensitivity by which
the audio input will control the
modulation.
BALANCE
0– 50 –100
Adjusts the volume balance
between the direct sound and the
effect sound.
PREAMP
Simulates the characteristics of a guitar amplifier.
Parameter Value
(Bold: default)
Explanation
AMP TYPE
JC-120,
NATURAL CLEAN,
FULL RANGE,
COMBO
CRUNCH , STACK
CRUNCH,
HIGAIN STACK, POWER
DRIVE, EXTREM LEAD,
CORE METAL
Selects the preamp type.
SPK TYPE
OFF,
ORIGINAL
, 1x8”,
1x10”, 1x12”, 2x12”,
4x10”, 4x12”, 8x12” Selects the speaker type.
GAIN 0–
50
–120 Sets the distortion of the amp.
T-COMP
-10– 0 –+10
Adjusts the sense of compression
of the amp.
BASS 0– 50 –100
Adjusts the tone for the low
frequency range.
MIDDLE 0–
50
–100
Adjusts the tone for the middle
frequency range.
TREBLE 0–
50
–100
Adjusts the tone for the high
frequency range.
PRESENCE
0– 50 –100
Adjusts the tone for the ultra high
frequency range.
MIC TYPE
DYN57 , DYN421,
CND451, CND87, FLAT
Selects the mic type.
MIC DIS
OFF MIC
, ON MIC
Sets the distance between the
mic and speaker.
MIC POS
CENTER , 1–10 cm Sets the mic position.
E.LEVEL 0– 50 –100
Sets the volume of the effect
sound.
DIST
This effects that distort the sound.
Parameter Value
(Bold: default)
Explanation
TYPE
VOCAL, BOOST, OD,
DS, METAL, FUZZ
Selects the distortion type.
TONE -50–
0
–+50 Sets the tonal character.
DIST
0– 50 –100 Sets the degree of distortion.
D.LEVEL
0
–100
Sets the volume of the direct
sound.
E.LEVEL
0–50– 100
Sets the volume of the effect
sound.