background image

Safety Information

4 - English

NOTE: 

This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 

reasonable protection against harmful interference in a residential installation. This 

equipment generates, uses, and can radiate radio frequency energy and, if not installed 

and used in accordance with the instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that interference will not occur in a 

particular installation.  If this equipment does cause harmful interference to radio or televi

-

sion reception, which can be determined by turning the equipment off and on, the user is 

encouraged to try to correct the interference by one or more of the following measures:

• 

Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment and receiver.

•  Connect the equipment to an outlet on a different circuit than the one to which the 

receiver is connected.

• 

Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following 

two conditions: (1) This device may not cause harmful interference, and (2) this device 

must accept any interference received, including interference that may cause undesired 

operation.

This Class B[*] digital apparatus complies with Canadian ICES-003.

These devices comply with FCC and Industry Canada RF radiation exposure limits set 

forth for general population. They must not be co-located or be operating in conjunction 

with any other antennas or transmitters.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is 

subject to the following two conditions:

(1) This device may not cause interference, and (2) this device must accept any interfer-

ence, including interference that may cause undesired operation of the device.

Remote control output power: 2.3 mW @ 2.4 GHz

Console output power: 1.5 mW @ 2.4 GHz

Changes or modifications not expressly approved by Bose Corporation could void the 

user’s authority to operate this equipment.

The temperature range of this product is 0° C to +55° C.

This product conforms to all applicable EU directive requirements. 

The complete declaration of conformity can be found at 

www.Bose.com/compliance.

Names and Contents of Toxic or Hazardous Substances or Elements

Part Name

Toxic or Hazardous Substances and Elements

Lead (Pb)

Mercury (Hg)

Cadmium (Cd)

Hexavalent (CR(VI))

Polybrominated Biphenyl (PBB)

Polybrominated  Diphenyl Ether (PBDE)

PCBs

X

0

0

0

0

0

Metal parts

X

0

0

0

0

0

Plastic parts

0

0

0

0

0

0

Speakers

X

0

0

0

0

0

Cables

X

0

0

0

0

0

0: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ/T 11353-2006. 
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T 11353-2006.

Apple, iPhone, iPod, and Mac are trademarks of Apple Inc., registered in the U.S. and other countries.

HDMI and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

©2013 Bose Corporation. No part of this work may be reproduced, modified, distributed, or otherwise used without written permission.

Summary of Contents for VideoWave III





















Reviews: