manualshive.com logo in svg

Bose Personalized Amplification System, Troubleshooting Manual

Share
Download
Bose Personalized Amplification System Troubleshooting Manual Download Page 28

28

TEST PROCEDURES

3. Channel 1 and 2 Mic Input Signal to
Noise Ratio (Dynamic Range) Tests

3.1

 Place a 1/4” mono shorting plug into the

Amp 2 IN and Amp 3 IN jacks on the right
hand side of the input/output panel. This will
disable the channel 2 and 3 amplifiers while
testing the channel 1 amplifier.

3.2

 On the left hand side of the input/output

panel, set the channel 1 Mic Trim control to
the 6 setting. Ensure that the Line In +20dB
gain and the Phantom Power push buttons
are not pushed in.

3.3

 Using a balanced XLR male input cable,

apply a 1 kHz, -30dBV signal to the channel
1 input.

3.4

 Reference a dB meter to the output level

at the Amp 1 OUT jack. Remove the input
signal and measure the A-Weighted output
level. It should be -80dB minimum.

3.5

 Move the shorting plug from the Amp 2

IN jack to the Amp 1 IN jack and repeat
steps 3.1 to 3.4 for the channel 2 Mic input.

4. Channel 1 and 2 Line Input Gain Tests

4.1

 Place a 1/4” mono shorting plug into the

Amp 2 IN and Amp 3 IN jacks on the right
hand side of the input/output panel. This will
disable the channel 2 and 3 amplifiers while
testing the channel 1 amplifier.

4.2

 On the left hand side of the input/output

panel, set the channel 1 Mic Trim control to
the 6 setting. Ensure that the Line In +20dB
gain and the Phantom Power push buttons
are not pushed in.

4.3

 Using an unbalanced 1/4” phono jack

input cable, apply a 1 kHz, -10dBV signal to
the channel 1 input.

4.4

 Reference a dB meter to the input level.

Measure the gain output at the Amp 1 OUT
jack. It should be +28.5 dB + 4dB.

4.5

 Move the shorting plug from the Amp 2

IN jack to the Amp 1 IN jack and repeat
steps 4.1 to 4.4 for the channel 2 Line input.

5. Channel 1 and 2 Line Input Frequency
Reponse and Distortion Tests

5.1

 Place a 1/4” mono shorting plug into the

Amp 2 IN and Amp 3 IN jacks on the right
hand side of the input/output panel. This will
disable the channel 2 and 3 amplifiers while
testing the channel 1 amplifier.

5.2

 On the left hand side of the input/output

panel, set the channel 1 Mic Trim control to
the 6 setting. Ensure that the Line In +20dB
gain and the Phantom Power push buttons
are not pushed in.

5.3

 Using an unbalanced 1/4” phono jack

input cable, apply a 1 kHz, -10dBV signal to
the channel 1 input.

5.4

 Use an 80kHz low-pass filter on your

measuring equipment. Reference a dB
meter to the input level. Measure the fre-
quency response at the Amp 1 OUT jack.
It should be 0dB + 3dB from 30Hz to 15kHz.

5.5

 Measure the Total Harmonic Distortion

(THD) level at the Amp 1 OUT jack. It should
be 0.25% max at 1kHz and 1.5% max at
15kHz.

5.6

 Move the shorting plug from the Amp 2

IN jack to the Amp 1 IN jack and repeat
steps 2.1 to 2.5 for the channel 2 Line input.

Summary of Contents for Personalized Amplification System



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands