background image

24 

6720819898 C  11/2017

2. 

Burn new fuel at a high temperature (ie with the primary air 

fully open) for a few minutes to establish a good fire before 

adjusting down the Primary Air Control.

3. 

Refuel little and often for clean, efficient burning.

4. 

When burning smokeless fuel, more primary air will increase 

the heat output and burn the fuel more quickly.

5. 

Your  burning  experience  with  your  stove  will  determine  the 
best setting for your installation.

ASH DISPOSAL

Ashes  should  be  removed  from  the  stove  every  few  days  or 

accumulation of ash can occur which will obstruct airflow through 

the burning wood. If ashes obstruct the airflow, poor burning of the 

wood is likely. Always empty the ash pan when it is cold, such as in 

the morning. Ashes should be placed in a metal container with a tight 

fitting lid. The closed container of ashes should be placed on a non 

combustible floor or on the ground, well away from all combustible 

materials, pending final disposal. If the ashes are disposed of by 

burial in soil or otherwise locally dispersed, they should be retained 

in  the  close  container  until  all  cinders  have  thoroughly  cooled. 

Other waste should not be placed in this container.

Your multifuel stove is a high efficiency stove and therefore requires 

little maintenance. It is important to perform a visual inspection of 

the ash panevery time it is emptied, in order to ensure that no parts 

have  been  damaged,  in  which  case  repairs  must  be  performed 

immediately.  Inspect  and  clean  the  chimney  and  connector  pipe 

periodically for creosote buildup or obstructions.

WOOD UTILISATION

Your  heating  unit  is  designed  to  burn  wood  or  Defra  exempt 

smokeless fuel. Waste and other flammable materials should not 

be burned in your stove. Any type of wood may be used in your 

stove, but specific varieties have better energy yields than others. 

This stove was tested using dry beech or birch wood - only use 

dry-seasoned wood (preferably hardwood) with a moisture content 

of less than 20%.

It  is  EXTREMELY  IMPORTANT  that  you  use  DRY  SEASONED 

WOOD or Defra exempt smokeless fuel in your multifuel stove. The 

wood should have dried for 9 to 15 months, such that the moisture 

content (in weight) is reduced below 20% of the weight of the log. 

It is very important to keep in mind that even if the wood has been 

cut for one, two or even more years, it is not necessarily dry, if it has 

been stored in poor conditions. Under extreme conditions it may 

rot, instead of drying. This point cannot be over-stressed; the vast 

majority of the problems related to the operation of a wood stove is 

caused by the fact that the wood used was too damp or has dried 

in poor conditions. These problems can be:

- ignition problems

- creosote build-up causing chimney fires

- low energy yield

- blackened stove windows

- incomplete log combustion

Smaller pieces of wood will dry faster. All logs exceeding 152mm 

in diameter should be split. The wood should not be stored directly 

on  the  ground.  Air  should  circulate  through  the  wood  stack.  A 

610mm to 1219mm air space should be left between each row of 

logs, which should be placed in the sunniest location possible. The 

upper layer of wood should be protected from the elements but not 

the sides. 

TESTING YOUR WOOD

When  the  stove  is  thoroughly  warmed,  place  one  piece  of  split 

wood (about five inches in diameter) parallel to the door on the bed 

of red embers.

Keep the air control full open by pulling on it and close the door. 

If  ignition  of  the  piece  is  accomplished  within  90  seconds  from 

the time it was placed in the stove, your wood is correctly dried. If 

ignition takes longer, your wood is damp.

If your wood hisses and water or vapour escapes at the ends of the 

piece, your wood is soaked or freshly cut. Do not use this wood in 

your stove. Large amounts of creosote could be deposited in your 

chimney, creating potential conditions for a chimney fire.

WARNING: Do not operate this appliance with 

the primary air control open for a long period of 

time. This will cause over firing of your appliance 

and may cause permanent damage.

1

2

3

4

5

6

7

8

9

10

11

12 13

14

15

16

USER INSTRUCTIONS

WARNING: Ashes could contain hot embers 

even after two days without operating the stove.

1

2

3

4

5

6

7

8

9

10

11

12 13

14

15

16

SAFETY NOTICE

If this stove is not properly installed, a house fire may result. To reduce the risk of fire, follow the 

installation instructions. 

Consult the municipal building control department or fire officials about permits, restrictions and 

installations requirements in the area.

Use carbon monoxide detectors in the room where the stove is installed.

Keep furniture and curtains well away from the stove.

Never use petrol,petrol-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or 

“freshen up” a fire in this stove. Keep all such liquids well away from the stove while it is in use.

In the event of a chimney fire, push the air control full closed to deprive the fire of oxygen. Call the fire 

brigade.

Do not connect to any air distribution duct or system.

A source of fresh air into the room or space heated shall be provided 

Only operate the stove with the door closed. Operating with the door open could cause over firing.

1

2

3

4

5

6

7

8

9

10

11

12 13

14

15

16

Summary of Contents for Worcester Greenstyle Hanbury 4





































Reviews: