Bosch WIW...V0 series Instruction Manual And Installation Instructions Download

Page: 36 / 56

Additional programme settings

Additional programme

settings

Additional programme settings

You can find an overview of all possible

additional settings on the

supplementary sheet for the installation

and operating instructions.
The settings vary depending on the

model.

Speed/Eco

(

, Speed Eco Perfect)

Button with two possible settings for

adapting the selected program:

■

Speed

Washing in a shorter time while

achieving a washing result that is

consistent with, but uses more

energy than, the selected program,

without the Speed/Eco setting.

Note:

Do not exceed the maximum

load.

■

Eco

Energy-optimised washing by

reducing the temperature while

achieving a washing result that is

consistent with the selected

program, without the Speed/Eco

setting.

Press the button to do this. First of all,

you can select the

Speed

setting. If you

press the button again, the

Eco

setting

is active. The respective symbol is

shown in the display when the setting is

activated.
If you press the button again, no setting

is active.

Summary of Contents for WIW...V0 series

























































Search results

Summary of Contents for WIW...V0 series

Reviews:

Related manuals for WIW...V0 series

Brands by name

Popular brands

Bosch WIW...V0 series, Instruction Manual And Installation Instructions

Search results

Summary of Contents for WIW...V0 series

Reviews:

Related manuals for WIW...V0 series

Brands by name

Popular brands