background image

 

 

 
 
 
BOSCH  844 AND 880 
 
SIMPLE INSTRUCTIONS 

 

 

Ph 377 7575 

 
 
ARMING IN AWAY MODE (full arm) 

 

Enter your code + AWAY     or      0 + AWAY 

 

or Press button 1 on pendant 

 
 

STAY 

Mode  allows  you  to  arm  the  system  with  predetermined  zones  disabled.  This  means 

that  you  can  partially  arm  the  system  at  night  while  you  are  still  at  home,  thus  giving  you 
personal protection. 
 

ARMING IN STAY MODE (partial arm) 

 

Enter your code + STAY     or     0 + STAY 

 

or Press button 2 on pendant. 

 
 

DISARMING 

 

Enter your code + AWAY 

 

or Press button 1 or 2 on pendant. 

 
 

PANIC ALARM

   

This will create an audible alarm

 

On code pad press STAY and AWAY simultaneously.  
On pendant press both buttons 1 & 2 simultaneously.  
 
 

TO SILENCE PANIC ALARM 

 

Enter your code + AWAY 

 

or Press either button 1 or 2 on pendant. 

 
 

Entry  time

  is  the  time  allowed  to  disarm  the  system  after  you  have  opened  the  first  entry 

delay zone. During entry time, the codepad will beep, warning you to disarm your system. If 
the system is not disarmed at the expiration of entry time, an alarm will be activated. 
 

Exit  time 

is  the  amount  of  time  you  have  to  leave  your  home  after  you  have  armed  the 

system. 

Summary of Contents for Solution 880






























Reviews: