Solution 16
plus
32
Bosch Security Systems 09/06 BLCC100R
Quick Start Guide
System > System Options >
General Options
MENU 7-7-0
1
Display LAN Fail
Y
2
Report LAN Fail
Y
3
Alarm On LAN Fail
N
4
Reserved
N
5
Can Change Own PIN Code
N
6
Monitor Default PIN Codes
Y
7
PIN Always Required
N
8
Display Menu Numbers
Y
Use Keys [
] and [
] to scroll up and down the option list. With option
selected press ON / OFF key to enable or disable option. [
] will display
to indicate option set. Press [OK] To Save when finished.
(*** System Wide Parameter ***)
System > System Options >
Area Options
MENU 7-7-1
1
Area 1 = Common Area
N
2
First To Open Last To Close
N
3
Reset Siren All Users (All Areas)
Y
4
Power Up In Same State As Powered Down
Y
5
Fault Acknowledge All Areas
Y
6
Delay Trouble Beeps
Y
7
Power Up Disarmed
N
8
Reserved
N
Use Keys [
] and [
] to scroll up and down the option list. With option
selected press ON / OFF key to enable or disable option. [
] will display
to indicate option set. Press [OK] To Save when finished.
(*** System Wide Parameter ***)
System > Options >
Keypad Idle Screen
MENU 7-7-2
0 = No Idle Screen
0
1 = Date and Time
2 = Time
3 = Custom Screen
(*** System Wide Parameter ***)
Use Keys [
] and [
] keys or enter 0 - 3 Then Press [OK] To Program
The Keypad Idle Screen - Single Option Only.
System > Options >
Keypad Hi/Lo Temp
MENU 7-7-3
0
0
˚
C
0
0
˚
C
(*** System Wide Parameter ***)
Hi TEMP
Lo TEMP
Use Keys [
] and [
] keys To Program The High / Low Keypad Monitor
Temperature. Max = 50 Min = 0
System > Installer Options >
Installer Options
MENU 7-7-4
1
Report/Log Entry/Exit Intstaller Menu
N
2
Report/Log Program Data Change
Y
3
Arm Only Installer Pin
N
4
Reserved
N
5
Auto Exit Installer Menu In 2 Hours
Y
6
Auto Exit Service mode In 2 Hours
Y
7
Reserved
N
8
Factory Defaulting Allowed
Y
Use Keys [
] and [
] to scroll up and down the option list. With option
selected press ON / OFF key to enable or disable option. [
] will display
to indicate option set. Press [OK] To Save when finished.
(*** System Wide Parameter ***)
System >Options >
Language
MENU 7-7-5
0 = English
0
1 = Alternate Language
(Enter Digits 0 – 15 To Program Area, Output or Access Group Number,
Then Press [OK] To Save
System > System Testing >
Walk Test All Zones
MENU 7-9-0
Battery Test
MENU 7-9-1
Testing The System
You will need to be in programming mode before accessing
the test functions listed below.
Walk Test
Use the walk test command MENU 3-9-0 to test and verify
that all zones work correctly.
External Audible Test
Use MENU 4-9-0 to test and verify that all horn speakers
operate. This test will sound the horn speaker for two
seconds.
Internal Audible Test
Use MENU 4-9-1 to test and verify that all 12 VDC sirens
operate. This test will sound the siren for two seconds.
Strobe Test
Use MENU 4-9-2 To test and verify that the strobe operates.
This test will turn on the strobe until you manually stop the
test.
Battery Test
Use MENU 7-9-1 to test the back-up battery that is
connected to the control panel.
