Bosch Rexroth IndraDrive CsDrive System with HCS01 Project Planning Manual Download Page 24

Page: 24 / 344

1.2.3

About this documentation

Purpose

Personal injury and property damage caused

by improper project planning for applications,

machines and installations!

WARNING

Observe the contents of the documentation relevant to your drive system

(see

chapter "Documentations" on page 25

This documentation contains the following:
●

Overview of the Rexroth IndraDrive Cs system

●

Description of the allowed combinations of Rexroth IndraDrive Cs sys‐

tem components

●

Selection of the system components of the Rexroth IndraDrive Cs sys‐

tem

●

Specification applying to all components (ambient and operating condi‐

tions)

●

Application description of system characteristics

Editions

Edition

Notes

Changes in comparison to previous edition:

Revised contents

●

Added technical data (inverter power section) for HCS01.1E-W0013

●

Analog current input (DA option): Updated electrical data

Changes in comparison to previous edition:

New contents

●

External braking resistors:
–

HLR01.2N-0K06-N100R-E-003-NNNN

–

HLR01.2N-0K06-N180R-E-007-NNNN

●

SB option (Safe Motion Bus)

●

EP option (Engineering interface)

●

SUP-E02-MSM-BATTERYBOX-xxxx battery box accessory

●

Encoder cable for MSM motors with M5 absolute value encoder (

RKG0065

)

Revised contents

●

Updated type code

●

HCS01.1E-W0018-A02 (inverter data): Frequency-dependent output currents

●

HAS09.1-001 (module bus cable shield connection) accessory

●

Updated encoder emulation data

●

Removed HAP01.1E standard control panel

Bosch Rexroth AG

DOK-INDRV*-HCS01******-PR05-EN-P

22/341

Rexroth IndraDrive CsDrive Systems with HCS01

System presentation

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands

Bosch Rexroth IndraDrive CsDrive System with HCS01, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands