Bosch Rexroth IndraDrive CsDrive System with HCS01 Project Planning Manual Download Page 146

Page: 146 / 344

X24 P2, X25 P1, communication

Control section type

Function

ECONOMY

sercos III, EtherCAT (S3)
Communication module for sercos III and EtherCAT field bus systems

BASIC

Multi-Ethernet (ET)
With the Multi-Ethernet communication module "ET", drive controllers can be integrated in differ‐

ent Ethernet field bus systems (e.g. sercos III, EtherCAT, EtherNet/IP or PROFINET IO).

ADVANCED

●

sercos III master (CC)
Is used as "master" for cross communication (CC = Cross Communication)

●

Multi-Ethernet (ET)
With the Multi-Ethernet communication module "ET", drive controllers can be integrated in

different Ethernet field bus systems (e.g. sercos III, EtherCAT, EtherNet/IP or

PROFINET IO).

Tab. 6-11:

X24 P2, X25 P1, communication

Description

The connection point complies with IEEE 802.3 standard.

Tab. 6-12:

Connection point

P1, P2

P1 means "Port 1" and P2 means "Port 2". Thereby, the error counter of the

firmware can be directly assigned to a Port.

Connection

sercos III, EtherNet/IP, PROFINET:
●

Input: arbitrary

●

Output: arbitrary

EtherCAT:
●

Input: X25 P1

●

Output: X24 P2

Bosch Rexroth AG

DOK-INDRV*-HCS01******-PR05-EN-P

144/341

Rexroth IndraDrive CsDrive Systems with HCS01

Mounting and installation

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands

Bosch Rexroth IndraDrive CsDrive System with HCS01, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands