Bosch Rexroth IndraControl VDP 92.3 Project Planning Manual Download Page 57

Page: 57 / 60

Index

Symbols

24 volt power unit 47

Accessories 47

Address assignment – digital 24 V inputs and out‐

puts 38

Addresses 49

Air pressure 16

Ambient conditions 15

Connection cables for the USB interface 48

Connection cable to the control cabinet PC 48

Connector panel of the Profibus interface 27

Contained substances

see "significant components" 45

Declaration of conformity 16

Digital 24 V inputs and outputs – address assign‐

ment 38

Digital inputs: Characteristics 30

Digital outputs: Characteristics 30

External hand-held terminal 31, 38

Handwheel 38

Handwheel interface 33

Hazardous substances 45

Helpdesk 49

Housing dimensions 19

Inappropriate use, 4

Consequences, exclusion of liability 3

Installation notes 21

Interface to the control cabinet PC 23

Internal handwheel 38

Internal handwheel(X82) 33

LEDs 36

Maintenance, 41

General information 41

LCD display 41

Maximum ambient temperature 15

Maximum temperature gradient 15

Mechanical strength 16

Mounting the operator panel 22

Operating modes 24

Packaging 45

Pin assignment X1S1: Current and Voltage Supply

Pin assignment X2/1, X2/2, X2O1: Digital 24 V in‐

puts and outputs 29

Pin assignment X2M1: Key Switches, Machine On/

Off, EMERGENCY STOP 31

Pin assignment X7P1: field bus interface PROFI‐

BUS DP 28

Pin assignment X81: External hand-held terminal

Pin assignment X82: Internal handwheel 33

Production processes 45

PROFIBUS DP- address settings 35

PROFIBUS DP module (GSD file) 38

Prohibited substances 45

Protective earth terminal 28

Relative humidity 15

Return of Products 45

S1: Dip switch 24

Safety instructions for electric drives 5

Service hotline 49

Service life

Backlight 17

Fans 18

Significant components 45

Software

Project Planning Manual | Rexroth IndraControl VDP 92.3

Electric Drives

and Controls

| Bosch Rexroth AG

51/52

Index

Summary of Contents for Rexroth IndraControl VDP 92.3





























































Search results

Summary of Contents for Rexroth IndraControl VDP 92.3

Reviews:

Related manuals for Rexroth IndraControl VDP 92.3

Brands by name

Popular brands

Bosch Rexroth IndraControl VDP 92.3, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraControl VDP 92.3

Reviews:

Related manuals for Rexroth IndraControl VDP 92.3

Brands by name

Popular brands