Bosch Rexroth IndraControl VDP 92.3 Project Planning Manual Download Page 30

Page: 30 / 60

6.1.3

S1 Dip Switch

Overview

Designation at the

housing

Switch type

Function

S1/switch 1

DIP switch

Without function

S1/switch 2

DIP switch

OFF: Cable length to the control cabinet

PC < 30 m
ON: Cable length to the control cabinet PC

> 30 m

Fig.6-3:

DIP switch on the VDP

Operating Modes

If the distance to the control cabinet PC does not exceed 5 m, the USB con‐

nection to the VDP can be executed in the USB 2.0 mode by using an additional

USB 2.0 cable. The S1-switch 2 must be in the "OFF" position.
If the cable is not used, the USB connection is executed using the USB 1.1.
The USB connection is executed in the USB1.1 mode. The S1-switch 2 must

be in the "OFF" position.
The USB connection is executed in the limited full speed mode. Only keyboards

and mice can be connected to the VDP. It is not allowed to integrate internal

HUBs into these USB devices. Other USB devices, such as memory sticks, are

not supported. The S1-switch 2 must be in the "ON" position.
For information on the cable lengths related to the display resolution, please

refer to

chapter 11.2 "Accessories" on page 47

6.1.4

24 VDC Power Supply

The connection is designed as spring terminal FK-MCP 1,5/3-ST-3,5, 3-pin,

grid 3.5 mm. To this connector terminal, cables with a cross section of maximum

1.5 mm

can be connected. For terminal connectors use copper conductors

only.

CAUTION

Material damages to electronics due to missing functional earth ground

connection!

Please ensure that the functional earth ground is connected, since the elec‐

tronics can be destroyed by a potential difference between the VDP 92.3 and

the VSBxx.3 or the VPBxx.3 if the voltage supply is interrupted at one device

only and established again.
The VDP is supplied with 24 V via X1S1.

Fig.6-4:

Interface to the control cabinet PC

Function

+24 V

24/52

Bosch Rexroth AG | Electric Drives

and Controls

Rexroth IndraControl VDP 92.3 | Project Planning Manual

Interfaces

Distance between the control cabi‐

net PC and the VDP is 5 m max

Distance between the control cabi‐

net PC and the VDP is 30 m max

Distance between the control cabi‐

net PC and the VDP is more than

30m

Summary of Contents for Rexroth IndraControl VDP 92.3





























































Search results

Summary of Contents for Rexroth IndraControl VDP 92.3

Reviews:

Related manuals for Rexroth IndraControl VDP 92.3

Brands by name

Popular brands

Bosch Rexroth IndraControl VDP 92.3, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraControl VDP 92.3

Reviews:

Related manuals for Rexroth IndraControl VDP 92.3

Brands by name

Popular brands