Bosch Rexroth IndraControl S67 Series Application Description Download Page 124

Page: 124 / 142

sercos

S3-BK-DI8

SBM

1FB2

Fig. 11-1:

Removing field bus coupler with carrier rail adapter from carrier

rail

11.2.5

Removing Field Bus Coupler from Profile Adapter

If the field bus coupler is mounted on a profile adapter, proceed with the re‐

moval as follows:

1. Disconnect the power supply from those devices on which the field bus

coupler has been mounted before starting the removal.

2. Unscrew the screws on which the nuts are fastened and remove the

field bus coupler from the profile rail of the system.

3. Unscrew the screws that connect the field bus coupler with the profile

adapter.

11.2.6

Connecting New Field Bus Coupler

To connect a S67-S3-BK-DI8-M8 field bus coupler, proceed as described in

the following chapters:
●

chapter 5 "Mounting the Field Bus Coupler" on page 27

●

chapter 6 "Connecting Data and Supply Cables" on page 35

●

chapter 7 "Commissioning" on page 43

11.3

Disposal

Do not dispose the IndraControl S67 components in the household waste;

comply with the regulations regarding the components. You can also contact

a certified disposal company.

Bosch Rexroth AG

DOK-CONTRL-S67S3BKDI8*-AP03-EN-P

Rexroth IndraControl S67 Sercos Coupler 8 Digital Inputs (M8)

122/139

Maintenance and Service

Summary of Contents for Rexroth IndraControl S67 Series















































































































































Search results

Summary of Contents for Rexroth IndraControl S67 Series

Reviews:

Related manuals for Rexroth IndraControl S67 Series

Brands by name

Popular brands

Bosch Rexroth IndraControl S67 Series, Application Description

Search results

Summary of Contents for Rexroth IndraControl S67 Series

Reviews:

Related manuals for Rexroth IndraControl S67 Series

Brands by name

Popular brands