Trouble shooting
en
55
3
Trouble shooting
Trouble shooting
Usually, faults are small matters that are easy to
eliminate. Please read the information in the table
before calling the after-sales service.
Display
Possible cause
Solution
None
The power supply has been disconnected.
Use other electrical appliances to check whether a short circuit
has occurred in the power supply.
The appliance has not been connected as shown
in the circuit diagram.
Make sure that the appliance has been connected as shown in
the circuit diagram.
Electronics fault.
If the fault cannot be rectified, inform the technical after-sales ser-
vice.
The displays flash.
The control panel is damp or there is something
on it.
Dry the control panel or remove the object.
The
Ù
indicator will flash in the
cooking zone displays
A fault has occurred in the electronics.
To acknowledge the fault, briefly cover the control panel with
your hand.
”ƒ
/
“‰ƒ‹ˆ
/
“ˆ‹‚†
The electronics have overheated and have
switched off the affected cooking zone.
Wait until the electronics have cooled down sufficiently. Then
touch any symbol on the control panel.
”…
/
“‰ƒ‹‰
/
“ˆ‹‚†
/
“‹ˆƒƒ
/
“‹‰ƒƒ
/
“‹Šƒƒ
/
“‹ˆƒ„
/
“‹‰ƒ„
/
“‹Šƒ„
The electronics have overheated and all the
cooking zones have been switched off.
Ӡ
+ power level and audible
signal
There is hot cookware near the control panel.
There is a risk that the electronics will overheat.
Remove the cookware that is causing the problem. The fault dis-
play goes out shortly afterwards. The cooking process can be
continued.
Ӡ
and audible signal
There is hot cookware near the control panel.
The cooking zone has been switched off to pro-
tect the electronics.
Remove the cookware that is causing the problem. Wait a few
seconds. Touch any touch control. When the fault display goes
out, you can resume cooking.
”‚
/
”‡
The cooking zone has overheated and has been
switched off to protect the work surface.
Wait until the electronics have cooled down sufficiently. Then
switch the cooking zone on again.
”‹
The transfer settings function cannot be acti-
vated.
Confirm the fault display by touching any sensor. You can cook as
usual without using the transfer settings function. Contact our
technical after-sales service.
”Š
The FlexPlus cooking zone will not activate.
Confirm the fault display by touching any sensor. You can use the
other cooking zones to cook as usual. Contact our technical after-
sales service.
”‰
The cooking zone has been operating continu-
ously for an extended period.
The automatic safety cut-out function has been activated. See the
section entitled
“ˆ‹‚‹
The hob is unable to connect to your home net-
work or the extractor hood.
Confirm the fault display by touching any sensor. You can cook as
usual without a connection.
If the message appears again, contact our technical after-sales
service.
“‰ƒ‹ƒ
The cooking sensor has overheated and the
cooking zone has been switched off.
Wait until the cooking sensor has cooled down sufficiently before
activating the function again.
“‰ƒ‹„
The cooking sensor has overheated and all the
cooking zones have been switched off.
If you are not using the cooking sensor, remove it from the cook-
ware and keep it away from the other cooking zones and sources
of heat. Switch the cooking zones back on.
“‰ƒ‹…
The battery in the cooking sensor is almost flat. Replace the 3 V CR2032 battery. See the section entitled
“‰ƒ‹†
The connection to the cooking sensor has been
broken.
Switch the function off and then on again.
“‰ƒ‹‡
The cooking sensor is broken/faulty.
Contact our technical after-sales service.
Do not place hot cookware on the control panel.
Summary of Contents for PXY8 D Series
Page 2: ...2 Ø cm ...
