English |
9
Bosch Power Tools
1 609 92A 1RE | (19.4.16)
5
Pedestal
6
Heat sink
7
Tripod mount 5/8"
8
Carrying handle
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Assembly
Battery Charging (Accessory)
Note:
The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the cordless worklight is switched off by means of a
protective circuit.
Do not continue to press the On/Off switch after the
cordless worklight has been automatically switched
off.
The battery can be damaged.
To remove the battery
3
, press the battery unlocking button
2
and pull the battery toward the rear out of the cordless work-
light.
Do not exert any force when doing this.
Observe the notes for disposal.
Operation
Initial Operation
Inserting the battery
Insert the charged battery
3
into lamp head
4
until it can be
felt to engage and faces flush against the lamp head
4
.
Standing Up
Carefully fold out the pedestal and place the cordless work-
light on the floor.
Ensure that it has a firm footing.
Fastening to the tripod
You can use the tripod mount
7
to screw the cordless work-
light onto a tripod.
Tighten the 5/8" screw.
Ensure that the tripod has a firm
footing.
Swivelling the Lamp Head (see figure A)
The lamp head is attached to the handle. The lamp head can
be set to five positions using the handle.
Switching On and Off
To
start
the cordless worklight, press the On/Off switch
1
.
To
switch off
the cordless worklight, press the On/Off switch
1
again.
To save energy, only switch the cordless worklight on when
using it.
Adjusting the Brightness
Press the On/Off switch
1
briefly to switch on the cordless
worklight at maximum brightness. To adjust the brightness in
2 stages, hold down the On/Off switch
1
until the required
brightness is obtained.
Temperature Dependent Overload Protection
When exceeding the allowable heat-sink temperature of
60 °C, the cordless worklight switches off. Allow the cordless
worklight to cool down, then switch the cordless worklight on
again.
Working Advice
Shortly before the cordless worklight switches off because of
an empty battery, it will flash 3 times and shine with reduced
brightness.
Maintenance and Service
Maintenance and Cleaning
The light source cannot be replaced. If the light source is
defective, the entire cordless worklight has to be replaced.
When the battery is no longer operative, please refer to an au-
thorised after-sales service agent for Bosch power tools.
The cordless worklight is maintenance-free and contains no
components that must be replaced or maintained.
To avoid damage, clean the plastic lens of the cordless work-
light only with a dry, soft cloth. Do not use cleaning agents or
solvent.
Cordless Worklight
GLI 18V-1900
Article number
3 601 D46 4..
Rated voltage
V=
14.4
18
Lighting duration, approx.
min/Ah
40
50
Total luminous flux
lm
1900
Permitted ambient
temperature
–
during charging
–
during operation* and during
storage
°C
°C
0...+45
–20...+50
Recommended batteries
GBA 14,4
GBA 18 V ...
GBA 18 V ...W
Recommended chargers
AL 18..
GAL 3680
GAL 18...W**
* Limited performance at temperatures <0 °C
**
only for wireless charging batteries
The colour rendition of illuminated objects can be distorted.
OBJ_BUCH-2712-002.book Page 9 Tuesday, April 19, 2016 2:10 PM
