English –
5
Note:
The
Bluetooth
® connection does not have to be activ-
ated manually.
Setting the assistance level
On the operating unit
(16)
, you can set the level of assist-
ance you want the eBike drive to provide you with while ped-
alling. The assistance level can be changed at any time, even
while cycling.
Note:
In some models, the assistance level may be preset
and cannot be changed. There may also be fewer assistance
levels available than stated here.
The following assistance levels are available as a maximum:
–
OFF:
Motor assistance is switched off. The eBike can just
be moved by pedalling, as with a normal bicycle. The
push assistance cannot be activated at this assistance
level.
–
ECO:
Effective assistance with maximum efficiency, for
maximum range
–
TOUR:
Steady assistance, long range for touring
–
SPORT/eMTB:
SPORT:
Powerful assistance, for mountain biking and
cycling in urban traffic
eMTB:
Optimum assistance whatever the terrain, rapid
acceleration when starting from a standstill, improved dy-
namics and top performance (
eMTB
only available in
combination with the drive units BDU250P CX, BDU365,
BDU450 CX and BDU480 CX. A software update may be
required.)
–
TURBO:
Maximum assistance even at high pedalling
speeds, for sport cycling
To
increase
the assistance level, press the
+
button
(15)
on
the operating unit repeatedly until the required assistance
level appears on the indicator. To
decrease
the assistance
level, press the
–
button
(12)
.
The requested motor output is displayed in the indicator
j
.
The maximum motor output depends on the selected assist-
ance level.
When the on-board computer is removed from the holder
(4)
, the assistance level that was last displayed is saved; the
motor output indicator
j
remains empty.
Switching the push assistance on/off
The push assistance aids you when pushing your eBike. The
speed in this function depends on the selected gear and can
reach a maximum of
6
km/h
. The lower the selected gear,
the lower the speed of the push assistance function (at full
power).
u
The push assistance function must only be used when
pushing the eBike.
There is a risk of injury if the wheels
of the eBike are not in contact with the ground while using
the push assistance.
To
activate
the push assistance, briefly press the
WALK
button on your on-board computer. After activation, press
the
+
button within 3 s and keep it pressed. The eBike drive
is switched on.
Note:
The push assistance cannot be activated at assistance
level
OFF
.
The push assistance is
switched off
as soon as one of the
following occurs:
– You release the
+
button;
– The wheels of the eBike are locked (e.g. by applying the
brakes or hitting an obstacle);
– The speed exceeds
6
km/h
.
The push assistance function is subject to local regulations;
the way it works may therefore differ from the description
above, or the function may even be deactivated completely.
Switching bicycle lights on/off
On the model on which the lighting is powered by the eBike
system, the front and rear lights can be switched on and off
at the same time via the on-board computer using the bike
light button
(1)
.
Check that your bike lights are working correctly before
every use.
With the light switched on, the lighting
f
indicator appears in
the status bar on the display.
Switching the bike lights on and off has no effect on the
backlighting of the display.
Lock (premium function)
The Lock function is available to purchase from the
<Shop>
in the eBike Connect app. Once the Lock function is
switched on by disconnecting the on-board computer, the
eBike drive unit assistance is deactivated. It can only then be
activated using the on-board computer belonging to the
eBike.
Detailed operating instructions can be found online at
www.Bosch‑eBike.com
Activity tracking
In order to record activities, you must be registered with and
logged into the eBike Connect portal or the eBike Connect
app.
To record activities, you must consent to the storage of your
location data in the portal and/or in the app. Without this,
your activities will not be shown in the portal or the app.
Your position is only recorded if the on-board computer is
connected to the eBike Connect app.
Once synchronisation is complete, the activities will be dis-
played in the app and in the portal whilst you are riding.
eShift (optional)
eShift is the integration of electronic gear-shifting systems
into the eBike system. The eShift components are electric-
ally connected to the drive unit by the manufacturer. The
separate operating instructions describe how to operate the
electronic gear-shifting systems.
ABS – anti-lock braking system (optional)
If the wheel is fitted with a Bosch eBike ABS with no external
control lights, the control lights will be shown on the
Nyon
(BUI350)
display when the system starts and in the event of
a fault. For detailed information on the ABS and how it
works, please refer to the ABS operating instructions.
Bosch eBike Systems
1 270 020 BN2 | (18.03.2020)
Summary of Contents for Nyon BUI350
Page 2: ...2 7 6 5 4 9 3 2 1 8 1 270 020 BN2 18 03 2020 Bosch eBike Systems ...
Page 3: ... 3 10 11 12 13 14 17 16 15 Bosch eBike Systems 1 270 020 BN2 18 03 2020 ...
Page 4: ...4 1 2 3 5 4 18 20 1 2 20 19 9 A B 1 270 020 BN2 18 03 2020 Bosch eBike Systems ...
Page 148: ...Svensk 16 1 270 020 BN2 18 03 2020 Bosch eBike Systems ...
