manualshive.com logo in svg

Bosch MTS 6534, User Manual, Page: 15 / 18

Share
Download
Bosch MTS 6534 User Manual Download Page 15

1 689 989 355

2019-04-08

| 

Bosch Automotive Service Solutions GmbH

Cleaning and Maintenance  |  MTS 6534 / MTS 6535  |  15

en

en

9.9 

PC Application is Unable to Communi-

cate with the VCI over Wireless

Check that the wireless card is properly seated in the 
VCI.

 

R

Confirm the VCI can connect over USB

If using point to point confirm the PC has a single 
dongle connected:

 

Connect  the VCI to the PC using USB

 

Confirm the communication is enabled and the IP 
configuration is properly set using the VCI Manager 
software

If using infrastructure wireless:

 

Contact your IT department and check that your PC 
is detecting the wireless access point, and the cor-
rect security settings have been configured for the 
VCI.

10.  Cleaning and Maintenance

10.1  Cleaning and Storing

The housing of the VCI module and the trigger switch may 
only be cleaned using a soft cloth and a neutral cleaning 
agent. Do not use any abrasive cleaning agent or rough 
cleaning cloths.

 

i

There are no user serviceable components inside 
the VCI Vehicle Communication Interface or the trig-
ger switch. Do not open the devices. Opening the 
devices will void the warranty.

 

R

If the VCI, connectors, or cables become dirty, they 
may be cleaned by wiping them with a rag lightly coat-
ed with a mild detergent or non-abrasive hand soap.

 

R

Do not immerse the VCI or any of its parts or accesso-
ries in water.

 

R

Although the VCI and accessories are water resistant, 
they are not waterproof; thoroughly dry them prior to 
storage.

 

R

Avoid using harsh solvents such as petroleum based 
cleaning agents, Acetone, Benzene, Trichloroethylene, 
etc.

10.2  Recovering the VCI Software

As a result of a power failure or a communications error 
during a software update, the VCI software may become 
corrupted. You may see several symptoms such as error 
messages directing you to go to RECOVERY mode or an 
inability to connect to a detected VCI.
The following two error messages generally occur during 
VCI Tester Software download. If you see either of these 
messages, perform the Recovery Procedure.

 

R

"Error reprogramming the VCI. Go to Recovery Mode."

 

R

"There was a problem reprogramming the VCI" 

10.3  Spare and wearing Parts

Component

Part Number 
Renault

Part Number 
Nissan

OBD-Cable DLC J1962, VCI, 1.5 m 

1)

7711392598 1699.200.366-879

USB A to USB B, 3 m cable 

1)

7711392597 F-00K-108-653-879

Wireless Adapter 802.11n 

1)

7711392599 1687.010.590-760

DLC1 Cable Adapter 

1), 2)

7711392595 1687.010.604-GS0

Cigarette Lighter Adapter 

1), 2)

7711392593 1687.010.605-GS0

Trigger Switch 

1), 2)

7711392594 1687.010.606-GS0

1)

 Wearing part

2)

 Special accessorie

Summary of Contents for MTS 6534



















Reviews:

No comments