Bosch MIC-7502-Z30B Installation Manual Download Page 33

MIC IP starlight 7000i

Illumination/Wiper | en

33

Bosch Security Systems

Installation Manual

2017.09 | 0.12 | F.01U.xxx.xxx

10

Illumination/Wiper

Notice!

The illuminator fields are available only when an illuminator is attached to a MIC7000 camera.

The default intensity for illumination (both IR and White light) is 33%.

IR mode

Select the appropriate IR mode to control the IR illuminators:

On

 - This mode turns on the illuminators. The illuminators will remain active until you

select another mode. In this mode, the camera provides a much better image at low light
levels.

Off

 - This mode turns off the illuminators.

Auto

 - This mode activates the illuminators in low-light scenes (for example, at night), and

deactivates the illuminators in scenes with bright light (for example, during a sunny day).

Auto

 (converted only) -

IR operation range

Select the appropriate range of operation for the IR illuminator:

1x to 30x (default)

5x to 30x

10x to 30x

20x to 30x

Max. IR intensity

Select the percentage of maximum intensity of the infrared (IR) light, from 0 to 100. The
default is 33.

No white light

Select 

On

 to disable the field 

White light illuminators

. The options in the field 

White light

illuminators 

are disabled.

Select 

Off

 to enable field 

White light illuminators

.

White light illuminators

Select 

On

 to turn on the 

White light illuminators

.

Select 

Off

 to turn off the 

White light illuminators

.

White light intensity

Select the degree of intensity of the White light.

Note

: This field is active only if the White light illuminator is 

On

.

White light timeout

Select 

On

 to enable a timeout for the White light feature. 

Select 

Off

 to disable the timeout.

The timeout turns OFF the White light, after the light has been ON but idle for some time, to
help to retain the life of the LEDs.

White light timeout [min]

Select the number of minutes (from 1 to 30) after which the White light will turn off after
activation.

Illuminator compensation

Select 

Auto

 to configure the camera to compensate automatically for the illuminator.

Select 

Off

 to turn off illuminator compensation.

Wiper

Summary of Contents for MIC-7502-Z30B
















































Reviews: