manualshive.com logo in svg

Bosch MIC-7502-Z30B, Installation Manual, Page: 13 / 47

Share
Download
Bosch MIC-7502-Z30B Installation Manual Download Page 13

MIC IP starlight 7000i

Installation Overview | en

13

Bosch Security Systems

Installation Manual

2017.09 | 0.12 | F.01U.xxx.xxx

4

Installation Overview

!

Caution!

Installation must be made by qualified personnel and conform to ANSI/NFPA 70 (the National
Electrical Code

®

 (NEC)), Canadian Electrical Code, Part I (also called CE Code or CSA C22.1),

and all applicable local codes. Bosch Security Systems, Inc. accepts no liability for any
damages or losses caused by incorrect or improper installation.

!

Caution!

ELECTRIC SHOCK HAZARD
To reduce the risk of electric shock, disconnect power to the camera and/or to the power
supply unit before moving the camera, before installing any accessories, and before mounting
the camera.

Notice!

To maintain the NEMA 6P rating when the camera is mounted to a MIC-DCA, installers must
ensure that the user-supplied cable glands or conduit connections have NEMA 6P ratings.

Notice!

Outdoor installation
For details about the proper configuration for installing your camera outdoors with surge and
lightning protection, refer to 

Best Practices for Outdoor Installation, page 37

.

Summary of Contents for MIC-7502-Z30B
















































Reviews:

No comments