background image

LTC 9384 Series | 

Instruction Manual

Installation

EN

| 13

Bosch Security Systems | September 1, 2004

FIGURE 12 Breather Hole

Proper installation of the pull seal is as follows:

1.

Remove the cradle assembly from the housing.

2.

Obtain a rubber pull seal (Part Number 
315 2569 001) from the hardware kit (see
FIGURE 13). An extra pull seal is also provided.

FIGURE 13 Pull Seal

3.

Insert the long end of the pull seal into the
breather hole starting from the front of the
endcap (see FIGURE 14).

FIGURE 14  Inserting the Pull Seal

4.

Grip the pull seal's long end from the back of
the front endcap. Steadily pull the long end until
the head of the pull seal is flat against the front
of the endcap (see FIGURE 15).

NOTE: The pull seal's long end will stretch
when pulled through the breather hole.

FIGURE 15  Installing the Pull Seal

5.9.2

Cradle Assembly

1.

Position the housing vertically and replace 
the cradle assembly by applying pressure 
onto the rear cap until the end of the cradle 
is approximately flush with the back of the
housing (see FIGURE 16).

FIGURE 16  Inserting the Cradle Assembly

CAUTION: If a pull seal is installed in the
breather hole, be careful not to pinch the head of
the pull seal. Damage to the pull seal may allow
water to enter the housing, causing damage to
the camera and lens.

2.

Tighten the retention screw, making sure it is
seated into the rear cap groove. If the housing
needs to be tamper-resistant, the LTC 9380/02
(purchased separately) should be installed at this
time.

3.

Attach the housing to the appropriate mount 
or pan/tilt per the instructions provided.
According to the orientation of the housing, the
cradle assembly may need to be rotated. To
rotate the cradle assembly (while mounted),
grasp the rear handle and rotate it to the desired
position. View the monitor while rotating.

Long End

Head

Front of 

Endcap

Pull Seal

Breather Hole

Cradle

Front Face

Breather Hole

Front Endcap

Rear Face of Head Should
Be Flush with Front Face 
of Front Endcap

Grip and Pull

Summary of Contents for LTC 9384 Series

















Reviews: