Operating the hotplate
en
15
9 Operating the hotplate
You can find out everything you need to know about
operating your hotplate here.
9.1 Fitting burner parts
You can find out how to correctly position the burner
parts here.
Requirement:
Ensure that the burner parts are clean
and dry.
1.
Ensure that the individual parts of the burners are fit-
ted in their exact position and are straight; other-
wise, this may result in ignition problems or prob-
lems during operation.
2.
Position the burner lid precisely on the burner head.
9.2 Important information about the gas hob
Follow these instructions when using your gas hob.
¡
A slight whistling when operating the burner is nor-
mal.
¡
Odour formation during the first uses is normal. This
does not indicate a risk or malfunction. It will stop
after a while.
¡
An orange flame is normal. This is caused by dust
in the air, overflowing liquids, etc.
¡
If the burner's flame accidentally goes out, switch off
the burner's selector and wait at least 1 minute be-
fore igniting the burner again.
¡
A few seconds after switching off the hob, you may
hear noises, such as a slight clicking, from the
burner. This is not unusual, but shows that the pilot
is deactivated.
¡
Keep the ignition plugs clean. If the ignition plugs
are dirty, the igniter is damaged. Clean the ignition
plugs regularly with a small, metal-free brush. En-
sure that the ignition plugs are not exposed to any
heavy knocks.
9.3 Operating the hotplate
You can ignite the gas burner as follows.
ATTENTION!
The burner may not ignite or the burner flame is not
even.
▶
Ensure that the hotplate burners are clean and dry.
▶
The burner cup and burner cover must be in exactly
the right position.
The burner may go out accidentally.
▶
If the burner's flame accidentally goes out, switch off
the burner's selector and wait at least one minute
before igniting the burner again.
1.
Place suitable cookware on the pan support.
→
2.
Press and hold the selector for the required burner
and turn it to .
3.
With the hotplate selector pushed in, press .
a
The gas begins to flow out and the gas burner ig-
nites.
4.
Press and hold the hotplate selector for approx. 1–3
seconds.
a
The safety pilot is therefore activated. If the gas
flame goes out, the gas supply is automatically shut
off by the safety pilot.
5.
Set the desired flame size.
The flame is not stable between settings Off and .
You must therefore always choose a position
between the large flame and small flame.
6.
Check whether the flame is burning.
If the flame is not burning, repeat the steps.
7.
To end the cooking process:
‒
Turn the hotplate selector clockwise to .
9.4 Manually igniting the appliance
Note:
In the event of a power cut, you can light the
burners manually.
1.
Place suitable cookware on the pan support.
2.
Push in the selector for your chosen burner and turn
it anti-clockwise to the power level you require.
Press and hold the selector.
3.
Light the burner with a gas lighter or a match. Keep
the selector pressed in for a few seconds after igni-
tion.
9.5 Recommended cooking settings
You can find an overview of different foods with appropriate heat settings here.
Notes
¡
The cooking time will vary depending on the type, weight, thickness and quality of the food.
¡
Select the right cookware size for each hotplate. The diameter of the cookware base should be the same size as
the hotplate.
¡
Use as little water as possible when cooking, so that the food retains its vitamins and minerals.
–
Use as little water as possible when cooking, so that the food retains its vitamins and minerals.
–
Select short cooking times so that the vegetables remain firm and full of nutrients.
Summary of Contents for HXA060B21Q
Page 43: ......
