Cleaning function
en
23
.
Cleaning function
Cleaning function
Use the "Pyrolytic self-cleaning" function to clean the
cooking compartment.
You can choose from three cleaning cycles.
The dirtier the cooking compartment and the longer the
dirt has been there, the more powerful the cleaning
cycle should be. It is sufficient to clean the cooking
compartment every two to three months. You can clean
it more frequently if necessary. Cleaning requires
approx. 2.5-4.8 kilowatt hours.
Notes
■
For safety reasons, the appliance door locks
automatically once a certain temperature is reached.
You will not be able to open it again until the lock
symbol
n
on the display has gone out.
■
The interior lighting will not come on while the
appliance is being cleaned.
:
Warning
Risk of burns!
■
The cooking compartment becomes extremely hot
during the cleaning function. Never open the
appliance door. Allow the appliance to cool down.
Keep children away from the appliance.
Risk of burns!
■
;
The appliance becomes very hot on the outside
during the cleaning function. Never touch the
appliance door. Allow the appliance to cool down.
Keep children at a safe distance.
:
Warning
Risk of harm to health!
The cleaning function heats up the cooking
compartment to a very high temperature so that food
remnants left over from roasting, grilling and baking will
burn off.This process releases vapours, which can
irritate the mucous membranes. While the cleaning
function is running, keep the kitchen well ventilated. Do
not remain in the room for long periods. Keep children
and pets away. Follow the instructions even when using
the Delayed start function with a delayed end time.
Before running the cleaning function
Make sure that the cooking compartment is empty.
Remove any accessories, cookware or shelf rails from
the cooking compartment. Please see the relevant
section for information on how to remove the rails.
~
"Rails" on page 24
Clean the appliance door and along the edges of the
cooking compartment in the area around the seal. Do
not scrub or remove the seal.
:
Warning
Risk of fire!
■
Loose food remnants, fat and meat juices may catch
fire when the cleaning function is in progress. Before
you start the cleaning function, always remove the
worst of the food residues and remnants from the
cooking compartment.Do not use the cleaning
function for cleaning accessories.
Risk of fire!
■
The appliance will become very hot on the outside
during the cleaning function. Never hang
combustible objects, e.g. tea towels, on the door
handle. Do not place anything against the front of
the appliance. Keep children away from the
appliance.
Risk of fire!
■
If the door seal is damaged, a large amount of heat
will be generated around the door. Do not scrub or
remove the seal. Never operate the appliance if the
seal is damaged or missing.
Setting the cleaning function
Make sure you follow all the preparation instructions
before setting the cleaning function.
The length of time each cleaning cycle runs for has
been preset and cannot be changed.
1.
Use the function selector to set Pyrolytic self-
clean
q
.
2.
Use the temperature selector to set the cleaning
cycle.
The length of each cycle will appear on the display.
The cleaning function will start in a few seconds. The
remaining time will count down on the display.
Ventilate the kitchen while the cleaning function is
running.
The appliance door will lock shortly after the
programme starts running. The
n
symbol will appear on
the display.
An audible signal will sound when the cleaning function
has finished. The time on the display will be zero.
Switch the appliance off by turning the function selector
to the "Off" position.
You will not be able to open the appliance door again
until the cooking compartment has cooled down
sufficiently and the lock symbol
n
on the display has
gone out.
Delaying the end time
You can delay the end time if required. Before starting,
touch the
v
button until the "End" symbol is highlighted
on the display. Use the
@
button to delay the end time.
The appliance will switch to standby after it is started.
Cycle
Cleaning perfor-
mance
Length of cycle
1
Gentle
Approx. 1 hour and 15 minutes
2
Medium
Approx. 1 hour and 30 minutes
3
Intensive
Approx. 2 hours