English - 4
Vario-jet-fan power lance
Aquatak 150/150 X
Twist the front ring to adjust from a pencil to a fan
jet and vice versa.
To apply the detergent twist the rear ring as
shown from high pressure mode to low pressure
mode.
To adjust the spray pattern twist the front ring.
Also refer to Advice on using pressure washer re-
garding the detergent suction rate.
Aquatak 160 X
Twist the nozzle sleeve to adjust from a pencil to
a fan jet and vice versa.
To apply the detergent move the nozzle from
high pressure mode to low pressure mode by pulling
the nozzle forward.
To adjust the spray patten twist the nozzle.
Also refer to Advice on using pressure washer re-
garding the detergent suction rate.
Roto power lance
Turn the vario-jet/fan power lance 9 90° anti-
clockwise. Extract the vario-jet/fan power lance.
(Aquatak 150/150 X)
Unscrew the vario jet-fan power lance 9 from the
power gun 7. (Aquatak 160 X)
Insert the roto-power lance 14 into the power
gun 7. Depress and turn the roto-power lance 90°
clockwise to lock in place. (Aquatak 150/150 X)
Screw the roto-power lance 14 into the power gun 7.
(Aquatak 160 X)
Starting
Connect the product to the mains supply ensuring
that the mains switch is in the (
) position.
Open water tap.
Press the safety lock 1 to release the trigger 2.
Fully press the trigger 2 until there is a constant flow
of water to clear the air from the machine and water
supply hose. Release trigger 2. Press the trigger
safety lock 1.
Turn on main switch 10.
Point the power gun 7 downwards. Press the trigger
safety lock to release the trigger 2. Fully press the
trigger 2.
Stopping
Release trigger 2. Press the trigger safety lock. The
power gun is now locked and cannot be operated ac-
cidentally.
Turn off the main switch 10.
Close water tap. Unplug the machine from the elec-
tric supply.
Press the trigger safety lock 1 to release the trig-
ger 2. Fully press the trigger 2 until there is no more
water pressure in the machine. Release trigger 2.
Press the trigger safety lock 1.
Disconnect water supply hose from machine and
water supply.
General
Ensure that the machine is on level ground.
Do not overreach with the high pressure hose or
move the pressure washer by pulling the hose, this
could cause the machine to become unstable and
fall over.
Do not kink or drive a motor vehicle over the high
pressure hose. Do not expose the high pressure
hose to sharp edges or corners.
Never use the roto nozzle to clean motor vehicles.
Operating with Detergents
Only use Bosch approved detergents. Unsuita-
ble detergents may damage the unit and the ob-
ject being cleaned.
/
Fill the detergent tank 6 with detergent, di-
lute as recommended. The tank(s) can be removed
to aid filling and emptying.
/
To spray detergent move vario-jet-fan power
lance to low pressure mode.
We recommend that you use detergent sparingly for
the sake of the environment. Observe the re-
commended dilution on the detergent label.
By offering you an individualised range of cleaning
and preserving agents, Bosch guarantees trouble-
free operation of the unit.
only Aquatak 150/160 X
The product is fitted with one detergent tank. The de-
tergent adjustment knob 11 is used to increase/de-
crease detergent flow.
Adjustments and using different
nozzles
Starting and Stopping
H
I
J
K
O
P
R
Advice using pressure washer
M
N
I
K
L
F 016 L70 723.book Seite 4 Donnerstag, 29. September 2011 1:16 13
16 • F 016 L70 723 • TMS • 13.09.11
