background image

Installation and Operating Instructions
Temperature Modulated with Electronic Ignition Suitable for heating potable water and space heating 
(Intended for variable flow applications)

FOR OUTDOOR INSTALLATIONS ONLY

Greentherm 9800 SEO 160/199 | SECO 199

Danger: If the information in this manual is not followed exactly, a fire or explosion 
may result causing property damage, personal injury or death.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of 
this or any other appliance.
Installation and service must be performed by a trained and certified installer, service 
agency or the gas supplier.

Improper installation, adjustment, alteration, service or maintenance can cause 
injury or property damage. Refer to this manual. For assistance or additional informa-
tion consult a qualified installer, service agency or the gas supplier.

Upon completion of the installation, these instructions should be handed to the user 
of the appliance for future reference.

What to do if you smell gas

Turn off the gas shut-off valve. Open windows and door if smell detected inside 
the house.

Do not try to light any appliance.

Do not touch any electrical switch, telephone, and do not use outlets.

Extinguish all open flames. Do not smoke! Do not use lighters!

Warn all occupants of the building. Do not ring doorbells!

If you can hear gas leaking, leave the building immediately. Prevent others from 
entering the building and notify the police and fire department from outside the 
building.

From outside the building, call the gas utility company and a trained and certified 
installer.

160 000/199 000 Btu- Natural Gas | 160 000/199 000 Btu - Liquefied Petroleum (LP) Gas

6 720 817 281 (2017/05) US

Summary of Contents for Greentherm 9800 SECO 199





















































Reviews: