English |
15
Bosch Power Tools
1 609 92A 2NA | (29.7.16)
Time Indication
The construction site radio is equipped with a time indication
with separate power supply. When back-up batteries with suf-
ficient capacity are inserted in the back-up battery compart-
ment (see “Inserting/Replacing the Back-up Battery”,
page 13), the time can be stored even when the construction
site radio is disconnected from the AC power supply or the
battery.
Setting the Time
– To set the time, press the button
10
until the hours indi-
cation flashes in display element
e
.
– Press the
seek button
12
or the
seek button
11
un-
til the correct hour setting is indicated.
– Press the button
10
again, so that the minutes indica-
tion flashes in display element
e
.
– Press the
seek button
12
or the
seek button
11
un-
til the correct minute setting is indicated.
– Press the button
10
a third time to store the time set-
ting.
Working Advice
Recommendations for Optimal Handling of the Battery
Protect the battery against moisture and water.
Store the battery only within a temperature range between
–20 °C and 50 °C. As an example, do not leave the battery in
the car in summer.
A battery that is new or has not been used for a longer period
does not develop its full capacity until after approx. 5 charg-
ing/discharging cycles.
A significantly reduced working period after charging indi-
cates that the battery is used and must be replaced.
Observe the notes for disposal.
Troubleshooting – Causes and Corrective Meas-
ures
When the corrective measures do not eliminate an error,
please contact an authorised service agent for Bosch power
tools.
Maintenance and Service
Maintenance and Cleaning
For safe and proper working, always keep the construction
site radio clean.
Wipe off debris using a moist and soft cloth. Do not use any
cleaning agents or solvents.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch’s application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the product.
Cause
Corrective Measure
Construction site radio inoperative
No power supply
Completely insert the power-
supply plug and plug-in con-
nector or the charged battery
pack
Construction site radio too
warm or too cold
Wait until the construction
site radio has reached oper-
ating temperature
Construction site radio inoperative on AC power supply
Power-supply plug or connec-
tion cable defective
Check the power-supply plug
and the connection cable,
and have them replaced as
required
Wrong power-supply plug in-
serted
Use the original Bosch power-
supply plug (also available as
spare part)
Construction site radio inoperative on DC power supply
Battery contacts contaminat-
ed
Clean the battery contacts
(e.g. by inserting and remov-
ing the battery several times)
or replace the battery
Battery pack defective
Replace the battery
Battery pack too warm or too
cold
Wait until the battery has
reached operating tempera-
ture
Construction site radio suddenly inoperative
Power-supply plug or battery
pack not properly or com-
pletely inserted
Plug in power-supply plug or
battery properly and com-
pletely
Bad radio reception
Interference from other de-
vices or insufficient set-up lo-
cation
Position the construction site
radio at another location with
better reception or with
greater clearance to other
electronic devices
Time indication faulty
Back-up batteries of clock
empty
Replace back-up batteries
Back-up batteries incorrectly
inserted (wrong polarity)
Insert back-up batteries cor-
rectly
Cause
Corrective Measure
OBJ_BUCH-2915-001.book Page 15 Friday, July 29, 2016 3:30 PM
