14
| English
The timer remains enabled until the measuring tool is
switched off or until the timer is switched off in the settings
menu.
Tool settings menu
Select the tool settings menu in the settings menu.
Use the button
(4)
[
+
] or the button
(11)
[
–
] to select the
required tool setting and confirm this by pressing the button
(13)
[
Func
]. Select the required tool settings.
To exit the tool settings menu
(o)
, press the on/off/delete
button
(9)
[ ] or the soft key
(12)
[
].
Tool settings
Language
Time & date
ft/m
Unit of measurement
Unit of measurement for angles
TrackMyTools
Tool information
Tone signals
Switch-off time
Dimmer
Display brightness
Display orientation
Setting the language
Select the "Language" option in the tool settings menu. Set
the required language and confirm this by pressing the
[
Func
] button
(13)
or the measuring button
(2)
[ ].
Setting the date and time
Select the "Time & date" option in the tool settings menu. Set
the date and time according to the instructions on the dis-
play and confirm these by pressing the [
] soft key
(12)
.
Note:
The date and time have to be reset after the batteries
are changed.
Changing the unit of measurement
Select the unit of measurement option in the tool settings
menu. The default unit of measurement is
m
(metres).
Set the required unit of measurement and confirm this by
pressing the button
(13)
[
Func
].
To exit the menu item, press the on/off/delete button
(9)
[
] or the soft key
(3)
[
]. The selected tool settings remain
saved after you switch off the measuring tool.
Changing the unit of measurement of an angle
Select the option for setting the unit of measurement for
angles in the tool settings menu. The default unit of measure-
ment for an angle is
°
(degrees).
Set the required unit of measurement for angles and confirm
this by pressing the button
(13)
[
Func
].
To exit the menu item, press the on/off/delete button
(9)
[
] or the soft key
(3)
[
]. The selected tool settings remain
saved after you switch off the measuring tool.
TrackMyTools
Select the "TrackMyTools" option in the tool settings menu.
Confirm the setting by pressing the [
Func
] button
(13)
.
Initial activation is required. Data can only be transmitted us-
ing a suitable app or computer program.
TrackMyTools can be deactivated again at any time.
The TrackMyTools setting (activated/deactivated) is saved
when the measuring tool is switched off.
Note:
TrackMyTools can only be used when batteries are in-
serted. To activate TrackMyTools after changing the batter-
ies, the measuring tool must be switched on briefly.
Display illumination
Select the dimmer option in the tool settings menu.
The display illumination is continuously switched on. If you
do not press any buttons, the display lighting is dimmed
after approximately 30 seconds to preserve the battery.
The time until dimming starts can be adjusted (tool settings).
The brightness of the display can be adjusted to the sur-
rounding conditions in multiple increments (tool settings).
Measuring functions
Note: Integrated help function
Help in the form of an animation is saved in the measuring
tool for each measuring function. To access this, select the
button
(13)
[
Func
], the button
(4)
[
+
] or button
(11)
[
−
]
and then the soft key
(3)
[
]. The animation shows you the
detailed procedure for the selected measuring function.
The animation can be stopped and started again at any time
using the soft key
(3)
[
]. You can scroll forwards and
backwards using the button
(4)
[
+
] and button
(11)
[
−
].
Measuring length
Select the length measurement mode
.
To switch on the laser beam, briefly press the measuring but-
ton
(2)
[ ].
To measure, briefly press the measuring button
(2)
[ ]. The
measured value will be shown at the bottom of the display.
09.06.2017
13:20:23
0.0º
23.198 m
m
9.279
m
13.919
m
18.558
m
4.640
Repeat the above-mentioned steps for each
subsequent measurement. The last measured
value is at the bottom of the display, the penul-
timate measured value is above it, and so on.
Continuous measurement
In continuous measurement mode, the measuring tool can
be moved relative to the target, during which the measured
value will be updated every half a second. You can, for ex-
ample, move a desired distance away from a wall while read-
ing off the current distance at all times.
Select the continuous measurement mode
.
To switch on the laser beam, briefly press the measuring but-
ton
(2)
[ ].
1 609 92A 4XP | (11.01.2019)
Bosch Power Tools
Summary of Contents for GLM 150 C
Page 4: ...4 X 1 1 A B 1 609 92A 4XP 11 01 2019 Bosch Power Tools ...
Page 5: ... 5 1 2 X 1 2 X 1 1 D C Bosch Power Tools 1 609 92A 4XP 11 01 2019 ...
Page 7: ... 7 m 0 500m 2x 1 000 1 2 3 1x0 5m 2x0 5m G Bosch Power Tools 1 609 92A 4XP 11 01 2019 ...
Page 8: ...8 90 180 180 90 180 180º 90º 90º 180º 180º H 1 609 92A 4XP 11 01 2019 Bosch Power Tools ...
